Manual Ferm WEA1057 (page 5 of 104) (All languages)

632779

Zoom out

Zoom in

1/104

against severe impact hazards (such as, but

not limited to) fragmenting abrasive discs/

grinding wheels, stones and other grinding

tools, explosive devices or corrosive fluids.

The helmet will only protect the eyes and face

from radiation and sparks.

• Remove ill fitting clothing, remove ties,

watches, rings, and other loose jewellery.

• Maintain correct balance and footing. Ensure

the floor is not slippery and wear non slip

shoes.

• Keep children and unauthorized persons

away from the working area.

• The materials which may come into contact

with wearer's skin could cause allergic

reactions to susceptible individuals.

Warning!

• Do not use the helmet if damaged or you

suspect it may be faulty.

• Do not use helmet unless you have been

instructed in its use by a qualified person.

• Do not get the helmet wet or use in damp or

wet locations.

• Do not leave work place with helmet in

lowered position, as bright light source may

darken cartridge unexpectedly.

• Do not place the helmet on a hot surface.

• Clean helmet (see section 5.5) and store the

helmet in a safe, dry, childproof location.

If, at any time, the face plate in the

cartridge fails to darken when exposed to

a welding spark, do not use. Remove

cartridge and return to your dealer for

checking. Continued use of the product

knowing that the auto darkening feature

is not functioning may damage your eyes

and cause blindness. Continued use of

the helmet which is not functioning will

invalidate the warranty and could prohibit

a successful claim on any insurance

company.

3. Instruction for use

Before using the helmet for welding

ensure you have read and understood

the safety instructions in section 2.

The helmet comes ready assembled but before

it can be used it must be adjusted to fit the user

properly.

Adjusting the fit of the helmet

Fig. 1

The overall circumference of the headband can

be made larger or smaller by first pushing the

knob to unlock and thereupon rotating the knob

on the back of the headband (Y) This can be done

whilst wearing the helmet and allows just the right

tension to be set to keep the helmet firmly on the

head without it being too tight.

If the headband is riding too high or too low on

your head adjust the strap which passes over the

top of your head. To do this release the end of the

band by pushing the locking pip out of the hole in

the band. Slide the two portions of the band to a

greater or lesser width as required and push the

locking pip through the nearest hole (W).

Test the fit of the headband by lifting up and

closing down the helmet a few times whilst

wearing it. If the headband moves whilst tilting re-

adjust it until it is stable.

Adjusting distance between helmet and face

Fig. 1

To adjust the distance between the helmet and

your face in the down position loosen the tilt knobs

on either side of the helmet and slide it nearer to

or further from your face. (Z) It is important that

your eyes are each the same distance from the

lens otherwise the darkening effect may appear

uneven. Re-tighten the tilt knobs when adjustment

is complete.

Adjusting angle of the mask in the down

position

Fig. 2

If the lens is not properly aligned with the eyes in

the down position the mask angle can be further

adjusted into one of three preset positions using

the tilt plat.

Behind each pivot knob on the sides of the helmet

there is a screw which passes through the side of

the mask and into one of the holes in the tilt plate

(A, B, C). Partially undo each screw anticlockwise

so that it withdraws out of the tilt plate but remains

in the side of the mask. Rotate the headband

assembly so that one of the alternative positions

is aligned with the end of the screw. Turn the

screws clockwise again so that they pass through

the holes thus fixing the position of the tilt plate.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm WEA1057 in the language / languages: All languages as an attachment in your email.

The manual is 6,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm WEA1057 Manual

Product: