764020

Ferm TSM1036 Manual

10
Zoom out
Zoom in
Previous page
1/136
Next page
10
EN
1. Remove the saw blade cover (31) by loosening
the Phillips screws (32).
2. Loosen the nut by attaching the large spanner
(29) to the nut and using the small spanner
(30) on the motor shaft in order to counteract.
Attention: turn the nut in the direction of
rotation of the saw blade.
3. Remove the outer flange and remove the saw
blade (4).
4. Carefully clean the saw blade flanges before
installing the new saw blade. Replace and
tighten the new saw blade in reverse order.
The arrow marked on the saw blade,
which indicates the direction of rotation,
must point in the same direction as the
arrow marked on the machine, the saw
blade teeth must point downwards on
the front of the saw.
• Before you start working with the saw again,
the functionality of the protective devices must
be checked.
•
Warning! After each saw blade change, check
that the saw blade guard (2) opens and closes
as required. Additionally check whether the saw
blade (4) runs freely in the saw blade guard (2).
• Warning! After each saw blade change, check
that the saw blade (4) can move freely in the
table insert (6), when in vertical position and
when tilted to 45°.
Fixing on a substructure
Fig. A
The mounting holes (20) on the machine frame
are used to attach the device on a solid, flat base
such as on a workbench. Matching mounting
material (screws, etc.) are available at specialist
stores.
Dust Extraction
Fig. I
The saw is equipped with a dust extraction
system.
• Insert the vacuum cleaner adapter (16) in the
dust extraction port (25).
• It is strongly advised to use a dust extraction
system that is suitable for the material
wherever possible.
• Regularly check and clean the suction
channels.
Storage of loose parts
Fig. A, I
When not in use, the push stick (3), Parallel guide
(7) and Mitre guide (14) can be attached. The push
stick (3) can be stored in the machine housing,
as shown on figure A. The Mitre guide(14) can be
fixed to the machine housing with the wing nut
(36) as shown in figure I.
4. OPERATION
Switching on/off
Fig A
• Press the switch into position ‘1’ to put your
machine into operation.
• To switch off the machine the same switch
needs to be pressed to position ‘0’
• Always keep the mains cable away from
moving parts.
Parallel guide
Fig. A, J, K
When slitting wood parts, the Parallel guide (7)
must be used.
• Mount the Parallel guide (7) on the table
surface (1) with the clamping plate (26);
Washers (27) and knobs (12): Outside of the
saw table: set screw (12) and washer (27);
Inside of the saw table: clamping plate (26).
User modes
The supplied Parallel guide (7) has two different
height guide surfaces, one on each side of
the guide. Use the lower height side for flat
workpieces, the higher stop height for tall
workpieces.
1. To change the height of the stop, open the
knobs (12) on the Parallel guide (7) and remove
it from the table.
2. Turn the Parallel guide (7) 180 ° so that the front
end points to the rear.
3. Tighten the knobs (12) again.
Cutting width
The Parallel guide (7) can be mounted on both
sides of the table surface (1).
1. Loosen the two knobs (12).
2. With the aid of the ruler (22) on the table surface
(1), the Parallel guide (7) can be adjusted to the
desired size.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm TSM1036 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1036 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info