764020
8
Zoom out
Zoom in
Previous page
1/136
Next page
8
EN
Warning! Do not use HSS blades.
Insert the push stick in its holder when not in
use.
Use a push stick or a push block to guide the
workpiece.
Warning! Do not use the saw for rebating
or grooving.
Only use saw blades, whose maximum speed
is at least the speed indicated on the saw and is
suitable for the material to be cut.
During the transport, the upper part of the saw
blade has to be covered, by the guard.
Switch off the machine immediately when you
discover:
A defective mains plug or mains lead.
A defective switch.
Overheating of the machine.
Smoke or odeur caused by scorched insulation.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in the
wall outlet.
Using extension cables
As a supply for this machine always use an
unloaded line and/or an extension cable with
conductors of at least 1,5 mm2 and protected
with a 16 A fuse. Be sure that this extension
cable is not longer than 20 metres.
This machine can be switched to the single-
phase network (230-240 V/50 Hz). If you are
in doubt about the earth of the electricity
provisions, consult an electrician first.
2. MACHINE INFORMATION
Intended use
This power tool is intended as a stationary
machine for making straight lengthways and
crossways cuts in hard and soft wood free from
foreign bodies such as nails, screws and mortar.
Technical specifications
Model No. TSM1036
Voltage 230-240V~
Frequency 50 Hz
Power input 800W
No load speed 2950/min
Bevel angles 0° <> +45°
Sawblade dimensions Ø 200×2,4 × Ø 16mm
Number of teeth 24T
Max. workpiece height 90º 43 mm
Max. workpiece height 45º 27 mm
Thickness of the riving knife 2.2 mm
Blade body thickness 1.8 mm
Weight 13 kg
Lpa (sound pressure level) 99.6 +3 dB(A)
Lwa (sound power level) 112.6 +3 dB(A)
Vibration value <2.5 m/s2
Vibration level
The vibration emission level stated in this
instruction manual has been measured in
accordance with a standardised test given in
EN 60745; it may be used to compare one tool
with another and as a preliminary assessment of
exposure to vibration when using the tool for the
applications mentioned
- using the tool for different applications, or with
different or poorly maintained accessories,
may significantly increase the exposure level.
- the times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns.
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2-6.
1. Table surface
2. Blade guard
3. Push stick
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm TSM1036 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1036 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info