Manual Ferm TSM1031 (page 9 of 64) (English, German, Dutch, French, Swedish, Spanish, Finnish)

510128

Zoom out

Zoom in

1/64

b. As a stationary machine on the subframe. In

this case the machine must be secured to the

subframe with 4 bolts and the subframe

anchored to the floor or to a floor plate with

dimensions of at least 1 square metre

Assembly of the bench saw on the workbench

Fig. B & C

Before adjusting the saw, make sure the

plug is removed from the socket.

Fig. B shows the distance of the holes to be drilled

in the workbench on which to fasten the machine.

Drill holes of 8 mm.

Only use the machine after it has been

assembled completely and it has been

screwed onto the workbench or the

frame.

• Fig. C shows the part to be sawn out (310 x

310 mm), so that the sawdust can fall through

it and piling up is prevented! Only if you do not

use an extraction system!

• Fasten the machine with bolts.

• If the frame is used, it must be fixed on the

floor with four screws and the machine must

be fixed on the frame with four screws. Check

the screws before switching the machine on.

Assemble undercarriage

Fig. G

• Turn the machine upside down.

• Remove the black plastic bottom plate by

unscrewing the 6 screws. (Fig. G-1).

• Unscrew the adjusting knob on the front and

tilt the motor (Fig. G-2), then remove the

transport packing (Fig. G-3).

• Now place one by one the uprights in the

casing of the sawing bench (Fig. G-4).

• Secure the uprights with 4 screws using a

screwdriver, do not completely tighten the

screws (Fig. G-5).

• Fit the 4 support bars, do not completely

tighten the screws (Fig. G-6)

• Fit the black plastic bottom plate and screw it

tight.

• Attach the rubber feet under the uprights (Fig.

G-7).

• Turn the machine into an upright position on a

flat surface and adjust the machine so that it

stands in a stable position, tighten all the nuts

and bolts (Fig. G-7).

Assemble bracket/push stick

• Attach the 2 brackets onto the casing of the

sawing bench and screw them tight (Fig. G-8).

• Place the push stick in the brackets.

Assembly and attachment of the rip fence

Fig. D

• Attach the aluminium fence (A) to the

positioning block (B).

• Now you can attach the complete rip fence to

the bench top.

• Slide the rip fence via one end of the

positioning rail (C) over the bench top.

• Adjust the position of the aluminium fence

profile (A) such that the end corresponds to

the rear edge of the saw.

Assembly of the riving knife and the

protective cap

Fig. E

• Turn the saw blade completely upwards.

• Remove the bench inlay.

• Assemble the riving knife on the set-up for this

purpose and use hereby the Allen screws and

the filling rings. Ensure that the riving knife

falls properly into the opening (= groove).

• Now put the inlay back in the bench and

fasten it.

• Now assembly the protective cap onto the

riving knife and use hereby the profiled nut

and self-locking nut.

Now lay a lath against the saw blade and

the riving knife and check whether it falls

properly into the extension of the saw

blade. If this is not the case: Loosen the

fastening bolts and place or remove the

filling rings.

• Above the saw table the radial distance

between the riving knife and the toothed rim of

the saw blade shall not at any point exceed 5

mm at the depth of cut set.

• The tip of the riving knife shall not be lower

than 5 mm from the tooth peak, as shown.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1031 in the language / languages: English, German, Dutch, French, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 2,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm TSM1031 Manual

Product: