Manual Ferm TSM1031 (page 8 of 64) (English, German, Dutch, French, Swedish, Spanish, Finnish)

510128

Zoom out

Zoom in

1/64

35. Avoid workpieces hitting back in your direction

by taking the following measures:

• Always use sharp saw blades.

• Do not saw too small workpieces.

• Never release the workpiece before it has

been completely pushed through the saw.

• Always adjust the guide parallel to the

saw blade.

• Never remove the saw protection.

36. Before you continue sawing, ensure that you

are standing firmly and that your hands are in

the required position.

37. Never use thinners to clean the machine. Only

use a damp cloth for cleaning.

38. Do not use saw blades which are damaged or

deformed.

39. Replace table insert when worn.

40. Use only saw blades recommended by the

manufacturer.

41. Take care that the selection of the saw blade

depends on the material to be cut.

42. Connect circular saws to a dust-collecting

device when sawing.

43. Use and correct adjustment of the riving knife

44. Use and correct adjustment of the upper saw

blade quard.

45. Take care when slotting.

Before use, remove the transport protection:

• Disassemble the bottom plate by loosening

the 4 screws.

• Remove the transport protection below motor.

• The handles for height and mitre setting of the

saw blade are located in the transport

protection inside the machine.

• Reassemble the bottom plate.

Switch off the machine immediately when you

discover:

• A defective mains plug or mains lead.

• A defective switch.

• Overheating of the machine.

• Smoke or odeur caused by scorched

insulation.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Replacing cables or plugs

Immediately throw away old cables or plugs when

they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

Using extension cables

• As a supply for this machine always use an

unloaded line and/or an extension cable with

conductors of at least 1,5 mm

and protected

with a 16 A fuse. Be sure that this extension

cable is not longer than 20 metres.

• Only connect your machine and/or extension

cable to an earthed electricity mains.

• This machine can be switched to the single-

phase network (230 V/50 Hz). If you are in

doubt about the earth of the electricity

provisions, consult an electrician first.

3. Assembly instructions

Assembly of the bench extensions

Fig. F

• Before attaching the bench extensions, first

remove the perforated base plate (you can

now also remove and discard the motor

protection materials).

• Once the bottom side is open, you can attach

the diagonal support struts to the bench saw.

• Now attach the bench extensions to the basic

bench top. Next, attach the extensions to the

diagonal support struts.

• Once all the extensions have been

assembled, re-attach the base plate (taking

care that all extensions are perfectly lined up

with the basic bench top itself).

• Lastly, attach the guide rail (with ruler) to the

front edge of the bench top.

Installation of the machine on a workbench or

on the subframe

This machine is a stationary machine and for

safety reasons must always be firmly installed and

not used for mobile applications.

You can install the machine in two ways:

a. As a stationary machine on a workbench. In

this case the machine must be secured to the

workbench with 4 bolts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1031 in the language / languages: English, German, Dutch, French, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 2,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm TSM1031 Manual

Product: