510106

Ferm SGM1011 Manual

7
Zoom out
Zoom in
Previous page
1/144
Next page
EN
7
and a slow speed will give a heavy coat. Apply
one coat at a time. If a further coat is required,
make sure you observe the manufacturers
drying time recommendations before applying a
second coat. When spraying small areas, keep
the output control on a low setting. This will avoid
using too much paint and prevent overspray.
Where possible, avoid stopping and starting when
spraying an object. This can lead to too much,
or not enough paint being applied. Do not tip the
spray gun to more than 45°.

Make sure that the machine is not live
when carrying out maintenance work on
the motor.
This machine has been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Troubleshooting
 

• Worn swirl head.
• Replace swirl head.
• Pick up pipe not in the right position.
• Re-adjust pick up pipe.
• Blocked pick up pipe.
• Clean with thinner.
• Blocked nozzle.
• Clean nozzle.
• Blocked filter.
• Clean with thinner.
• Control knob needs adjustment.
• Adjust.
 
• Volume adjustment is not correct.
• Adjust.
• Paint too thick.
• Check viscosity of the paint.
 
• Too much paint.
• Adjust the volume clockwise to reduce
spraying. Two thin coats are better then
one thick coat.
• Viscosity too low.
• Check viscosity.
 
• Spray gun not clean, or not lubricated,
resulting in piston being stuck in cylinder.
• Disassemble spray gun and clean with
thinner.
 
• No electricity.
• Check power supply.
 
• Poor output adjustment.
• Re-adjust.
• Not enough paint in the container resulting in
air being sucked in.
• Refill with paint.
• Not diluting properly or not passing pick up
pipe completely.
• Check pick up pipe and viscosity level.
 
• Incorrect solvent is used.
• Use correct solvent.
• Spray gun too far from the surface.
• Hold spray gun closer to the object.
• Paint too thick.
• Thin the paint.
Cleaning and maintenance
Fig. G
Always remember to disconnect from the
mains supply before cleaning the spray
gun or paint container.
It is essential that the spray gun is cleaned
thoroughly after every use. Failure to clean will
almost certainly result in blockages and the spray
gun might not operate next time it is being used.
The warranty does not cover malfunction due to
failure to clean the spray gun properly.
The following actions must be taken after every
use and if the spray gun is not going to be used for
a longer period. Not taking the following actions
can cause the paint to dry;
• Switch off the machine.
• Press the trigger so the paint will flow back in
the container.
• Unscrew the container and pour the paint
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm SGM1011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm SGM1011 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info