Manual Ferm SGM1011 (page 6 of 144) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

510106

Zoom out

Zoom in

1/144

masking tape. The paint or fluid to be sprayed

should be thoroughly mixed and free from lumps

or other particles. Many substances can be

sprayed with your spray gun, but always check

the manufacturers recommendations before

purchasing your paint.

Thinning

Always remember to disconnect from the

mains supply before filling the paint

container with sprayable material.

Most paints are supplied ready for brush

application and will need to be thinned before

they are suitable to be sprayed. Follow the

manufacturers advice on thinning the paint when

used with a spray gun. The viscosity cup will help

you to determine the correct viscosity of paint to

be used. To determine the correct viscosity, fill

the cup to the brim with the paint. Measure the

amount of time it takes for the cup to empty back

into the can.

The table below shows recommended times for

different types of material.

 

Alkyd/Oil based primers from 25 to 40

Alkyd/Oil based farnish from 15 to 40

Acryl/Water based primers from 25 to 40

Acryl/Water based farnish from 20 to 35

Impregnation solvents for wood,

paint removers, oils undiluted

Disinfectant, insectides undiluted

Car paint from 20 to 35

This tool is not suitable for spraying dispersions

and latex paint, caustic solutions, acidic coating

materials, coating materials with granules

or solids as well as spray and drip-impeding

materials.



• Insert the air hose (4) tightly in the connection

on the machine.

• Insert the air hose (4) tightly in the connection

on the spray gun.

Switch on/off

• Push the on/off switch (6) on the machine to

switch the machine off or on.

• Press the trigger on the air gun to start

spraying.

Adjusting the jet settings

Fig. F

A. Horizontal flat jet. This setting is used for

horizontal surfaces

B. Vertical flat jet. This setting is used for vertical

surfaces

C. Circular jet. This setting is used for corners,

edges and hard to reach surfaces.

If the paint takes longer than the recommended

time to empty, then further thinning is required.

Mix in a small quantity of the appropriate thinner

and use the viscosity test until the correct

thickness is achieved. Some sprayable materials

contain particles and lumps. These materials

should be strained before filling the paint

container.



Fig. C

Fill the paint container with the correctly thinned

and strained paint. Connect the spray gun to

the mains supply. Aim the spray gun at a piece

of scrap material and operate the trigger switch

until paint is spraying. Adjust the output control

(2) until the required volume of paint is spraying.

Turn the output control in a clockwise direction

(B) to reduce the flow and anti-clockwise (A) to

increase the flow. Adjustment of the output control

will affect the spray pattern. A poor spray pattern

will concentrate the paint in the centre of the spray

and give a blotchy finish. A good spray pattern

will give even distribution of paint throughout the

pattern.



Fig. D

To obtain the best results, keep your spray gun level

and parallel to the surface at all times. Keep the

nozzle 25 - 30 cm from the surface and spray evenly

from side to side or up and down. Do not spray at an

angle as this will lead to paint runs on the surface.

Use smooth and even strokes. When spraying large

areas, use a criss-cross pattern as shown.

Fig. E

Never start or stop the spray gun while it is aimed

at the surface to be sprayed. Evenly control the

speed of movement of the spray gun. A fast speed

of movement over the surface will give a thin coat

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm SGM1011 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm SGM1011 Manual

Product: