To fit the flexible nozzle, unscrew the basket nozzle and
attach the flexible nozzle in it's place. Replace the basket
nozzle on the end of the flexible nozzle and tighten.
CLEANING AND MAINTENANCE
Fig. G.
Always remember to disconnect from the mains
supply before cleaning the spray gun or paint
container.
It is essential that the spray gun is cleaned thoroughly
after every use. Failure to clean it will almost certainly
result in blockages and it may not operate when you next
come to use it! The guarantee does not cover cleaning a
sprayer that has not been properly cleaned by the user.
The following action must be taken after every
use.
1. Empty any remaining material from the container.
2. Clean the container thoroughly with the thinner
thatwas used.
3. Pour some thinner into the container and spray
through the spray gun until only clean thinner is
coming out of the nozzle.
4. Thoroughly clean the paint pick up pipe and filter
with thinner.
5. Clean the basket and nozzle and remove any other
debris or paint that remains.
6. Turn the spray gun upside down and apply a few
drops of light oil to the two apertures (F). This will
lubricate the piston and cylinder.
If your spray gun should require extra internal
cleaning, it may be necessary to disassemble it. If
so the following action should be taken.
1. Remove the plug from the mains socket.
2. Remove paint container, pick up pipe and filter.
3. Undo the 4 screws (G).
4. Take off the pump assembly.
5. Release the nozzle (H), valve (J), piston (K) and spring
(L).
6. Clean the cylinder (M) and all parts thoroughly with
solvent.
7. Apply a few drops of light lubricating oil to the piston,
spring and cylinder.
8. Reassemble the spray gun.
TROUBLE SHOOTING
1. Motor hums but does not spray or irregular
spraying.
• Worn swirl head
Replace swirl head.
• Pick up pipe not int the right position
Re-adjust pick up pipe.
• Blocked pick up pipe
Clean with thinner.
• Blocked nozzle
Clean nozzle.
• Blocked filter
Clean with thinner.
• Control knob needs adjustment
Adjust.
2. Atomization is not good.
• Volume adjustment is not correct.
Adjust.
• Paint too thick
Check viscosity of the paint.
3. Over painting.
• Spray gun not clean, or not lubricated, resulting in
piston being stuck in cylinder
Disassemble spray gun and clean with thinner.
• Too much paint
Adjust the volume clockwise to reduce spraying. Two
thin coats are better then one thick coat.
• Viscosity too low
Check viscosity
4. Motor louder than normal.
• Spray gun not clean, or not lubricated, resulting in
piston being stuck in cylinder
Disassemble spray gun and clean with thinner.
5. No spray, no sound.
• No electricity
Check power supply.
6. Operating sound not right.
• Poor output adjustment
Re-adjust
• Not enough paint in the container resulting in air
being sucked in.
Refill with paint.
• Not diluting properly or not passing pick up pipe
completely.
Check pick up pipe and viscosity level.
7. “Orange Skin” excessive fogging.
• Incorrect solvent is used
Use correct solvent.
• Spray gun too far from the surface.
Hold spray gun closer to the object.
• Paint too thick
Thin the paint
MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
The Ferm machines have been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper machine care and regular cleaning.
CLEANING
Keep the ventilation slots of the machine clean to
prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.
If the dirt does not come off use a soft cloth moistened
with soapy water. Never use solvents such as petrol,
alcohol, ammonia water, etc. These solvents may
damage the plastic parts.
Ferm 5
VEDLIGEHOLD
Afbryd altid strømforsyningen til redskabet i
forbindelse med vedligeholdsaktiviteter på
motoren.
Fermmaskinerne er fremstillet til at blive brugt i lang tid
med et minimum af vedligehold. En fortsat
tilfredsstillende funktion afhænger af god behandling af
maskinen og regelmæssig rengøring.
RENGØRING
Hold maskinens ventilationsåbninger rene, for at
forekomme en overophedning af motoren. Rengør
maskinhuset regelmæssigt med en blød klud, helst lige
efter brugen. Hold ventilationsåbningerne fri for støv og
urenheder. Hvis urenhederne ikke kan fjernes med tør
klud, brug en blød klud med sæbevand. Brug aldrig
opløsningsmidler som petroleum, alkohol,
ammoniakvand el. lign. Disse opløsningsmidler kan
skade plastikdelene.
SMØRING
Maskinen kræver ingen yderligere smøring.
FEJL
Skulle der opstå en fejl, f. eks. efter slidtage af en del, tag
da kontakt med Deres lokale Fermforhandler. Bag I
dette manual kan De finde en udbredt oversigt over de
reservedele der kan bestilles.
MILJØ
For at undgå at maskinen bliver udsat for skader under
transporten, bliver den leveret i en kraftig forpakning.
Størstedelen af forpakningsmaterialerne kan genbruges.
Bring disse materialer til de pågældende genbrugssteder.
Aflever Deres kasserede maskine til Deres lokale Ferm-
forhandler. Her vil den blive den blive kasserest på en
miljømæssig sikker måde.
GARANTI
Garantibestemmelserne findes i det separat vedlagte
garantikort.
Vi erklærer at under almindeligt ansvar, at dette
produkt er i overenstemmelse med følgende
normer eller normative dokumenter
EN50144-1, EN50144-2-7,
EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3
i henhold til bestemmelserne i direktiverne:
73/23/EEC
89/336/EEC
frà 18-10-2004
ZWOLLE NL
W. Kamphof
Kvalitetsafdeling
CE
ı
KONFORMITETSERKLÆRING
(
DK
)
44 Ferm
