Manual Ferm PRM1015 (page 6 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

510113

Zoom out

Zoom in

1/132

Mounting and removing cutters

Fig. B

Only use cutters with a shaft diameter which

corresponds with the size of the collet. Only use

cutters which are suited for the maximum speed

of the machine. The cutter diameter should not

exceed the maximum diameter (see ‘Technical

specications’).

Never tighten the collet nut, if there is no router bit

in the collet; the collet may be damaged.

• Pressthespindlelock(7)andturnthecollet

nut (6) until it engages in the lock. Keep the

spindle lock pressed during this procedure.

• Openthecolletnutusingthespanner.

• Placethecuttershaftinthecollet.

• Tightenthecolletnutsothatthecutteris

locked properly.

• Openthecolletnutwhenyouwanttoreplace

a cutter.

Adjusting the parallel fence ruler

The parallel fence is a useful tool for precision

routingataxeddistancefromtheedgeofthe

workpiece.

• Placethedesiredcutterinthetool.

• Slidetheparallelguidewiththeguiderodsinto

the baseplate and tighten at the required

measure with the wing bolts

Mounting the template guide

Fig. D

The template guide is a handy aid for cutting a

pattern.

• Mountthetemplateguide(23)ontherouter

base (3) using the screws (22).

Mounting the adapter for dust extraction

Fig. E & F

Usethedustadapterfortheextractionofdust.In

case the adapter is not mounted on the machine,

follow these instructions.

• Mountthedustadapter(24,Fig.E)withthe

screws (22) on the cutter sole (3).

• Placethedusttube(25)inthedustoutput(16

Fig. F).

• Placethetubeofyourvacuumcleaneronthe

dust tube (25, Fig. F).

Keep the outlet of the machine behind

the machine for a good view on the

workpiece.

4. OPERATION

The ON/OFF switch

• Toswitchonthetool,pressandholdtheon/off

switch (1, Fig. A1, page 2).

• Ifyoureleasetheon/offswitch(1,Fig.A1,

page 2), the tool will be switched off.

• Youcanlocktheon/offswitchbypressingthe

on/off switch (1, Fig. A1, page 2) and then

button (5, Fig. A1, page 2). The switch lock

canbereleasedbybrieypressingtheon/off

switch (1, Fig. A1, page 2).

• Donotputthemachinedownwhenthemotor

is still running. Do not place the machine on a

dusty surface. Dust particles may enter the

mechanism.

Usage tips

• Afterswitchingthemachineon,makesurethe

machine reaches full speed before using it on

the workpiece.

• Clamptheworkpieceandmakesurethatthe

workpiece cannot slide from under the

machine during the cutting activities.

• Holdthemachinermlyandmoveitevenly

over the workpiece. Do not force the machine.

• Onlyusecutterswhichdonotshowanysigns

of wear. Worn cutters have a negative effect

ontheefciencyofthemachine.

• Alwaysswitchoffthemachinerstbefore

removing the plug from the wall socket.

Speed Preselection

The required speed can be preselected with the

thumbwheel. Also during running the rotational

speed can be adjusted.

1 – 2 = low speed

3 – 4 = medium speed

5 – 6 = high speed

Max = maximum speed

The required speeds depends on the material and

can be determined by practical testing.

Furthermore router bits with a large diameter

need a lower rotational speed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm PRM1015 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm PRM1015 Manual

Product: