Manual Ferm MSM1037 (page 10 of 92) (English, German, Dutch, French, Italian, Swedish, Spanish, Finnish)

634080

Zoom out

Zoom in

1/92

Adjusting the cutting angle

Fig. 2

Adjusting Mitre Angles

The mitre angle can be set between 45° left side

and 45° right side

- Loosen the locking knob (10).

- Turn the saw table left or right until the angle

indicator (23) indicates the required angle.

- Tighten the locking knob (10).

Pre-settings (quick settings) on the following

degrees: -45°, -40°, -35°, -30°, -25°, -20°, -15°,

-10°, -5°, 0°, 5°, 10°, 15°, 20°, 25°, 30°, 35°, 40°,

45°.

Adjusting Bevel Angles

Fig. 1 and 3

The bevel angle can be set between 0° and 45°.

Adjust sliding fence accordingly!

See chapter 3, sliding fence.

- Loosen the adjusting knob (9).

- Tilt the saw by using the handle until the angle

indicator (14) indicates the required angle.

- Tighten the adjusting knob (9).

Changing the carbon brushes

Fig. 2

- Disconnect the machine from the power

supply.

- Unscrew the two covers (4) on the front and

backside of the motor housing.

- Replace the carbon brushes with the exact

type of brushes.

- Tighten the covers (4) again.

Note: Always replace both carbon brushes at the

same time, never use a mixture of old and new

brushes.

Mounting the dust bag

Fig. 1

Press in the clamp of the dust bag (13) and slide

it onto the opening on the back of the machine.

The dust bag stays in place when you release the

clamp.

4. OPERATION

Using the mitre saw

Fig. 1

Before use, always check for faults or

defects!

• Setthedesiredsawingangleofthemachine.

• Puttheplugintothesocket.

• Fixthepieceofworkinplaceusingtheclamp

(7): make sure that the material is well clamped

in place!

• Holdthematerialtightlyontheleftsidewhile

making sure that you keep a safe distance

from the blade of the saw.

• Turnonthemachineusingtheswitch(1).

• Makesurethatthesawbladehasreachedfull

speed before allowing it to touch the piece of

work to be sawn.

• Useknob(3)toraisetheprotectivecoverlock.

• Nowbringthesawslowlydownwardssothat

the saw blade saws through the piece of work

and passes through the slot in the table. Do

not put any pressure on the saw. Give the

machine time to saw through the piece of

work.

• Bringthemachinegentlyupagainandswitch

it off by letting go of the switch (1).

Using the laser

Fig. 2

• Toswitchonthelaser,presstheon/offswitch

• Toswitchoffthelaser,releasethe

on/off switch 2.

5. SERVICE AND MAINTENANCE

Always make sure that the machine is not

connected to the mains electricity when

you carry out any maintenance of the

mechanism.

Cleaning

Clean the machine housing regularly with a soft

cloth, preferably after each time you use the

machine. Make sure that the ventilation slots are

free of dust and dirt. For stubborn dirt use a soft

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1037 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 7,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm MSM1037 Manual

Product: