Manual Ferm MSM1037 (page 9 of 92) (English, German, Dutch, French, Italian, Swedish, Spanish, Finnish)

634080

Zoom out

Zoom in

1/92

against the stop and can’t move, so it cannot

till or turn or move while sawing.

x) Never use the machine to saw pieces of work

that are to small that they cannot be secured

safely. Small pieces of wood or other objects

that come in contact with the rotating saw

blade can strike the operator or out standers

with high speed.

y) When sawing always use the additional

supports.

z) For sawing of large piece work that not

supported. Use extra supports.

aa) Never make warning signs on the machine

unrecognizable. Technical information or

machine type information must be always

visible on machine.

At the end of the sawing process, keep the saw

head downstairs, switch off the machine and

wait until the all moving parts has come to a stop

before you take your hands off the machine.

3. ASSEMBLY AND

ACCESSORIES

Installation of the mitre saw

• Placeonesidebar(21)ontheright-handside

of the machine and the other sidebar on the

left-hand side of the machine.

• Placetheworkpiececlamp(7)ontheleftor

right side of the machine.

• Holdthehandgripandmovethesawslightly

downwards and then pull the pin (5) out slightly

so that saw moves upwards.

Note: Never use the mitre saw without the

extension pieces supplied. Make sure that they

are correctly mounted.

Mounting the anti-tip over support.

• Theanti-tipoversupport(24)ispremounted.

• Alwaysextendtheanti-tipoversupportwhen

using the machine.

Sliding fence

Fig. 2

For safety reasons, this machine is equipped with

a moveable guide fence to used in normal and

bevel cutting.

• Fornormalstraightcross-cutsandmitrecuts,

always adjust the sliding fence (8)(12) to the

end and fix well to provide safety support for

work piece.

• Forbevelcuts,adjusttheslidingfence(8)(12)

to a suitable position as close as to the saw

blade surface but avoid interfere the saw blade

movement and ensure to fix well.

Changing the saw blades

Fig. 4 and 5

Only use saw blades that are sharp and

undamaged. You must immediately

replace chipped or bent saw blades.

DANGER: Do not use any blade larger than the

stated capacity of the saw. It may come into

contact with the blade guard and cause harm.

Do not use a blade too thick to allow the outer

blade washer to engage with the flats on the

spindle. This will prevent the blade screw from

securing the blade on the spindle.

Do not use this saw to cut metal or masonry

• Disconnectthemachinefromthepowersupply.

• Removethescrew(19)thatholdstheretraction

arm(20).

• Pressthesawbladelockbutton(22)andhold.

Rotate the saw blade carefully by hand until the

blade locks.

• Usehexkeytoremovethesawbladebolt(17)

by loosening in a clockwise direction.

• Liftthebladecover(6)upwardsusingunlock

button (3) and hold it.

• RemovetheFlange(18)andthesawblade.

• Replacethesawblademakingsurethatthe

arrow marked on the saw blade must point in

the same direction as the arrow shown marked

on the machine. The saw blade teeth must

point downwards.

• Lowerthebladecover(6).

• ReplaceFlangeandfixthesawbladebolt(17)

use the saw blade lock button (22) to secure

tightly.

• Attachtheretractionarm(20)backby

tightening the screw (19).

• Rotatethesawblademanuallyandcheckifthe

guard operates freely.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1037 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 7,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm MSM1037 Manual

Product: