634079

Ferm MSM1035 Manual

9
Zoom out
Zoom in
Previous page
1/104
Next page
9
EN
• Pressthelockingpaddle(11)whenturningthe
baseplate, release the paddle before reaching
the requested degrees and the plate with
“click” into the pre-setting itself.
Adjusting Bevel Angles
Fig. 1 and 3
The bevel angle can be set between 0° and 45°.
• Loosentheadjustingknob(9)
• Tiltthesawbyusingthehandleuntiltheangle
indicator (14) indicates the required angle.
• Tightentheadjustingknob(9)
Changing the carbon brushes
Fig. 2
• Disconnectthemachinefromthepower
supply
• Unscrewthetwocovers(4)onthefrontand
backside of the motor housing.
• Replacethecarbonbrusheswiththeexact
type of brushes
• Tightenthecovers(4)again.
Note: Always replace both carbon brushes at the
same time, never use a mixture of old and new
brushes.
Mounting the dust bag
Fig. 1
Press in the clamp of the dust bag (13) and slide
it onto the opening on the back of the machine.
The dust bag stays in place when you release the
clamp.
4. OPERATION
Using the mitre saw
Fig. 1
Before use, always check for faults or
defects!
• Setthedesiredsawingangleofthemachine.
• Puttheplugintothesocket.
• Fixthepieceofworkinplaceusingtheclamp
(7): make sure that the material is well clamped
in place!
• Holdthematerialtightlyontheleftsidewhile
making sure that you keep a safe distance
from the blade of the saw.
• Turnonthemachineusingtheswitch(1).
• Makesurethatthesawbladehasreachedfull
speed before allowing it to touch the piece of
work to be sawn.
• Useknob(3)toraisetheprotectivecoverlock.
• Nowbringthesawslowlydownwardssothat
the saw blade saws through the piece of work
and passes through the slot in the table. Do
not put any pressure on the saw. Give the
machine time to saw through the piece of
work.
• Bringthemachinegentlyupagainandswitch
it off by letting go of the switch (1).
Using the slide-function
Fig. 1
The machine must be firmly bolted to a
workbench.
Use the slide-function for sawing wide
workpieces:
• Fixthepieceofworkinplaceusingtheclamp
• Loosentheknob(12)
• Slidethemachinecompletelytowardsyourself
• Turnonthemachineusingtheswitch
• Bringthesawslowlydownwardssothesaw
blade saws through the piece of work
• Pushthemachineslowlybackwards
• Bringthemachinegentlyupagainandswitch
it off by letting go of the switch
Using the laser
Fig. 2
• Toswitchonthelaser,presstheon/offswitch
2.
• Toswitchoffthelaser,releasethe
on/off switch 2.
5. SERVICE AND MAINTENANCE
Always make sure that the machine is
not connected to the mains electricity
when you carry out any maintenance of
the mechanism.
Slide rails
Dirt can damage the slide rails and thereupon the
operating of the machine.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm MSM1035 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1035 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 7,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info