Manual Ferm MSM1035 (page 8 of 104) (English, German, Dutch, French, Italian, Swedish, Spanish, Finnish)

634079

Zoom out

Zoom in

1/104

machine type information must be always

visible on machine.

At the end of the sawing process, keep the saw

head downstairs, switch off the machine and

wait until the all moving parts has come to a stop

before you take your hands off the machine.

3. ASSEMBLY AND

ACCESSORIES

Installation of the mitre saw

• Placeonesidebar(21)ontheright-handside

of the machine and the other sidebar on the

left-hand side of the machine.

• Placetheworkpiececlamp(7)ontheleftor

right side of the machine.

• Holdthehandgripandmovethesawslightly

downwards and then pull the pin (5) out slightly

so that saw moves upwards.

Note: Never use the mitre saw without the

extension pieces supplied. Make sure that they

are correctly mounted.

Mounting the anti-tip over support.

• Mountthesupportbracket(24)intotheslotin

the rear of the base.

• Tightenthescrewstosecurethesupport

bracket.

Sliding fence

Fig.2

For safety reasons, this machine is equipped with

a moveable guide fence to used in normal and

bevel cutting.

• Fornormalstraightcross-cutsandmitrecuts,

always adjust the sliding fence (8) to the end

and fix well to provide safety support for work

piece.

• Forbevelcuts,adjusttheslidingfence(8)

to a suitable position as close as to the saw

blade surface but avoid interfere the saw blade

movement and ensure to fix well.

Changing the saw blades

Fig. 4 and 5

Only use saw blades that are sharp and

undamaged. You must immediately

replace chipped or bent saw blades.

DANGER: Do not use any blade larger than the

stated capacity of the saw. It may come into

contact with the blade guard and cause harm.

Do not use a blade too thick to allow the outer

blade washer to engage with the flats on the

spindle. This will prevent the blade screw from

securing the blade on the spindle.

Do not use this saw to cut metal or masonry

• Disconnectthemachinefromthepowersupply.

• Removethescrew(20)thatholdstheretraction

arm to the blade cover.

• Removethescrew(19)inordertoremovethe

bolt-cover by lifting the blade cover (6) upwards.

• Bothsawbladebolt(17)andFlange(18)should

be visible now like shown in fig. 5.

• Pressthesawbladelockbutton(22)Rotatethe

saw blade carefully by hand until the blade locks.

• Usehexkeytoremovethesawbladebolt(17)

by loosening in a clockwise direction.

• RemovetheFlange(18)andthesawblade

• Replacethesawblademakingsurethatthe

arrow marked on the saw blade must point in

the same direction as the arrow shown marked

on the machine. The saw blade teeth must point

downwards.

• Fixthesawbladebolt(17)usethesawblade

lock button (22) in order to secure tightly

• Lowerthebladecover(6)inorderforthebolt-

cover to fall back into place and tighten the

screw (19)

• Attachtheretractionarmbackontotheblade

cover (6) by tightening the screw (20)

• Rotatethesawbladeandcheckiftheguard

operates freely

Adjusting the cutting angle

Fig. 2.

Adjusting Mitre Angles

The mitre angle can be set between 45° left side

and 45° right side

• Loosenthelockingknob(10)

• Pressthelockingpaddle(11)andturnthesaw

table left or right by the locking knob (10) until

the angle indicator (23) indicates the required

angle.

• Releasethelockingpaddle(11)andtightenthe

locking knob (10)

Pre-settings (quick settings) on the following

degrees: -45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°,

30°, 45°.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1035 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 7,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm MSM1035 Manual

Product: