632713
14
Zoom out
Zoom in
Previous page
1/36
Next page
Garantía
Lea atentamente las condiciones de garantía indicadas en la tarjeta de garantía que aparece en este manual de instrucciones.
CE DECLARACIÓN DE CONFORMIDAD (E)
Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas o documentos normalizados:
EN ISO11806, EN ISO14982, EN ISO3744
según las regulaciones:
98/37/EC, 2000/14/EC
Del 01-06-2006
ZWOLLE NL
J.A. Bakker - van Ingen J. Lodewijk
CEO Ferm BV Quality Manager Ferm Global
Es nuestra política mejorar continuamente nuestros productos y por tanto nos reservamos el derecho a cambiar las características del
producto sin previo aviso.
Ferm BV • Lingenstraat 6 • 8028 PM Zwolle • Holanda
Ferm 59
GB
D
NL
F
E
P
Remove three screws (H). Remove the skirt (A). Use the holding pin to prevent the collar from turning while removing the stringhead (turn
CLOCKWISE).
Leave the holding pin (B) in place.
Be sure the blade centre hole is correctly sized to the collar arbour.
Install blade (D) with teeth pointing CLOCKWISE as shown in the illustration.
Install flange (F) with FLAT SURFACE facing blade.
Note: Make sure the blade is centred on the collar arbour.
Tighten nut (C) securely by turning it COUNTERCLOCKWISE with the socket wrench (G). Remove holding pin.
Fuel and lubrication
Fuel
Use regular grade unleaded petrol mixed with 40:1 custom 2-cycle engine oil for best results. Use mixing ratios as in the FUELMIXING
TABLE.
Never use straight petrol in your unit. This will cause permanent engine damage and invalidate the manufacturer’s warranty for
that product. Never use a fuel mixture that has been stored for over 90 days.
If a 2-cycle lubricant other than custom lubricant is to be used, it must be a premium grade oil for 2-cycle air cooled engines mixed
at a 40:1 ratio. Do not use any 2-cycle oil product with a recommended mixing ratio of 100:1. If insufficient lubrication is the cause
of engine damage, it will invalidate the manufacturer’s engine warranty.
Mxing fuel
Add the oil to an approved fuel container followed by the petrol to allow incoming petrol to mix with the oil. Shake the container to ensure
thorough mixing.
Lack of lubrication invalidates the engine warranty. Petrol and oil must be mixed at 40:1.
Fuel mixing table
Petrol 40:1 Ratio Custom Lubricant
1 U.S. Gal. / 3.2 oz. 95 ml (cc)
5 Litres / 4.3 oz. 125 ml (cc)
1 lmp. Gal. / 4.3 oz. 125 ml (cc)
Mixing Procedure:
40 Parts Petrol to 1 part Lubricant
1ml = 1cc
Recommended fuels
Some conventional types of petrol are blended with oxygenates such as alcohol or an ether compound to meet clean air standards. Your
engine is designed to operate satisfactorily with any petrol intended for automotive use including oxygenated petrol.
4. OPERATING INSTRUCTIONS
Shoulder harness
Fig. 9A- 9B
Put the harness on so the shoulder strap is over your LEFT shoulder.
Attach the harness clip (A) to the ring (B) mounted on the shaft.
Adjust the length of the shoulder strap so the stringhead is parallel to the ground as it hangs from the strap. Afew practice swings without
starting the engine should be made in order to determine the correct balance.
Note: Detach the shoulder harness from the unit before starting the engine.
Starting cold engine
Fig. 10A- 10H
Note: To minimize the load on the engine during starting and warm-up, trim the excess cutter line to 13cm.
Move ignition switch to “RUN (I)” position.
14 Ferm
GB
D
NL
F
E
P
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm LTM1010 - FPCT 32CC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm LTM1010 - FPCT 32CC in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 9,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info