(ON)
(OFF) (. 2)
1. .
2.
.
3. .
4.
.
5.
.
.
,
.
:
.
!
•
!
•
.
.
.
,
.
•
,
.
,
.
•
.
•
.
•
.
•
.
!
.
(. 3).
5.
!
( )
.
.
,
.
.
, , ..
.
!
-
IP 34 ( )!
.
,
.
:
•
,
•
,
• ,
. (
5 ).
.
,
,
+5°C.
. ,
.
,
().
Ferm 65
Electricity
•We strongly recommend the use of an Residual
Current Device (RCD) of not more than 30 mA, at
the plug socket when using this appliance.
•All electrical connections e.g. extension cable, must
be of an approved waterproof type for outdoor
use and marked accordingly. Extension cables must
be threecore, one of which is EARTH.
Persons
•Never allow children or people unfamiliar with
these instructions to use the appliance. Local regu-
lations may restrict the age of the operator.
•Never mow while people, especially children, or
pets are nearby.
•The operator or user is responsible for accidents or
hazards occurring to other people or their property.
Preparation
•While mowing, always wear substantial footwear
and long trousers.
•Do not operate the appliance when barefoot or
wearing open sandals.
•Thoroughly inspect the area where the appliance is
to be used and remove all stones, sticks, wires,
bones, and other foreign objects.
•Before using, always check if the blades, blade bolts
and cutter assembly are not worn or damaged.
Replace worn or damaged blades and bolts in sets
to preserve balance.
•On multi-bladed appliances, take care as rotating
one blade can cause other blades to rotate.
Operation
•Mow only in daylight or in good artificial light.
•Avoid operating the appliance in wet grass, where
feasible.
•Always be sure of your footing on slopes.
•Walk, never run.
•For wheeled rotary mowers, mow across the face
of slopes, never up and down.
•Exercise extreme caution when changing direction
on slopes.
•Do not mow excessively steep slopes.
•Use extreme caution when reversing or pulling the
appliance towards you.
•Stop the blade(s) if the appliance has to be tilted for
transportation when crossing surfaces other than
grass, and when transporting the appliance to and
form the area to be mowed.
•Never operate the appliance with defective guards
or shields, or without safety devices, for example
deflectors and/or grass catchers, in place.
•Switch on the motor according to instructions and
with feet well away from the blade(s).
•Do not tilt the appliance when switching on the
motor, except if the appliance has to be tilted for
starting. In this case, do not tilt it more than abso-
lutely necessary and lift only the part which is away
from the operator. Always ensure that both hands
are in the operating position before returning the
appliance to the ground.
•Do not put hands or feet near or under rotating
parts. For rotary mowers, keep clear of the dis-
charge opening at all times.
•Never pick up or carry an appliance while the motor
is running.
•Pull the plug from the socket:
•whenever you leave the machine;
•before clearing a blockage;
•before checking, cleaning or working on the
appliance;
•after striking a foreign object. Inspect the appliance
for damage and make repairs as necessary;
•if the appliance starts to vibrate abnormally
(check immediately).
MAINTENANCE AND STORAGE
•Keep all nuts, bolts, and screws tight to be sure the
appliance is in safe working condition.
•Check the grass catcher frequently for wear of
deterioration.
•Replace worn of damaged parts for safety.
•For cylinder mowers, be careful during adjustment
of the appliance to prevent entrapment of the fin-
gers between moving blades and fixed parts of the
appliance.
•For rotary mowers, ensure that only replacement
cutting means of the right type are used.
3. ASSEMBLY
We recommend assembling the lawnmower in the
enclosed space on an even surface or on a special
working table. You will need a cross-tip screwdriver
during the assembly. Start the assembly after the iden-
tification of all parts (fig. 1)
•Upon removal of the lawnmower from the box,
put the lower part of the handle (5) in the apertu-
res of the body. Afterwards, lift the cover and fas-
ten the ends of the handle in the body with self-
tapping screws from the back side.
•Fasten the cable hanger (10) to the upper part of
the handle (6).
•Connect the cable to the lawnmower’s handle with
two clamps.
•Join the upper part of the handle (6) with lower
parts (5) and fasten thereof with a screw (7) and a
nut (8), placed into a plastic assembly wrench.
•Screw the wheels (11 and 12) on. All wheels should
be fastened on the same height: 4 different mowing-
heights are possible.
•The both parts of the grass reservoir (4) shall be
pushed into the apertures until hearing a click.
REPLACING THE CUTTING BLADE
•Switch off and remove the plug from mains before
replacing the blade.
•Note that the wings of the knife shall be directed
upwards for fastening.
•A flat or other hexagon spanner of 24 size is used
for unscrewing and screwing of the blade.
•Please note that the head of the screw fastening
the blade is made from plastic material; according-
ly, the force applied onto the screw during the
fixing of the blade shall be 10-16 Nm.
•Replace the cutting knife with the knife of the type
specified only.
4Ferm
