763898

Ferm JSM1034 Manual

8
Zoom out
Zoom in
Previous page
1/44
Next page
8
EN
4. OPERATION
Switching on and off
Fig. A
• To switch the machine on, push the switch
forward and press the On/off switch (1).
• To switch the machine off, release the On/off
switch (1).
Setting the speed
Fig. A
The speed adjustment wheel (5) is used for setting
the speed. The ideal speed depends on the profile
and the teeth of the saw blade and on the material
to be worked.
Do not set the speed during use.
• Turn the speed adjustment wheel (5) to the
required position.
- For hard materials, use a saw blade with fine
teeth and select a lower speed.
- For soft materials, use a saw blade with coarse
teeth and select a higher speed.
Adjusting the bevel angle
Fig. A, D
1. Loosen the bolts (16), using the hex key (13).
2. Adjust the baseplate (9) to the desired position
(0°- 45°). The sawing angle (bevel) can be read
on the scale (7).
3. Tighten the bolts (16), using the hex key (13).
It is possible to store the hex key onto the
machine, as shown on Fig. A.
Adjusting the pendulum action
Fig. A
The pendulum action switch (6) is used to set the
way in which the teeth of the saw blade grip the
material. The pendulum action switch can be set
to 4 positions:
0 - No pendulum action
1 - Small pendulum action
2 - Medium pendulum action
3 - Large pendulum action
The required pendulum action can be determined
by practical testing, although the following
instructions can be observed:
• Soft material (wood, plastics etc.): set the
pendulum to level II or III. For a finer and
cleaner saw cut, use pendulum level 0 or I.
• Thin material, use pendulum level 0.
• Hard material (hardwood, steel etc.): set the
pendulum to level 0.
• Curves: set pendulum to level 0.
Dust extraction
Fig. E
• Connect the hose of a vacuum cleaner to the
dust extraction adapter (8).
Note: the dust blow function must be de-
activated when using a vacuum cleaner.
Dust blow function
Fig. G
The cutting line can be kept clear of chips and
debris by using the dust blow function.
• To activate the dust blow function, move the
dust blower switch (2) to the right, as shown
on figure G1.
• To de-activate the dust blow function, move
the dust blower switch (2) to the left, as shown
on figure G2.
Optimum use
• Clamp the workpiece. Use a clamping device
for small workpieces.
• Draw a line to define the direction in which to
guide the saw blade.
• Firmly hold the machine by the grip.
• Set the sawing speed.
• Set the mitre angle.
• Switch on the machine.
• Wait until the machine has reached full speed.
• Place the saw shoe on the workpiece.
• Slowly move the machine along the pre-drawn
line, firmly pressing the saw shoe against the
workpiece.
• Do not apply too much pressure on the
machine. Let the machine do the work.
• Switch off the machine and wait for the
machine to come to a complete standstill
before putting the machine down.
5. MAINTENANCE
Before cleaning and maintenance,
always switch off the machine and
remove the mains plug from the mains.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm JSM1034 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm JSM1034 in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info