763897

Ferm JSM1033 Manual

8
Zoom out
Zoom in
Previous page
1/72
Next page
8
EN
Replacing the saw blade
Fig. A, B
When mounting the saw blade, wear
protective gloves. Danger of injury when
touching the saw blade.
Only use saw blades that correspond
with the characteristic data given in the
operating instructions.
Fold the Guard (12) upwards before replacing
the saw blade. Always saw with the guard folded
downwards.
Mounting the saw blade
Make sure the blade holder is free of material
debris (such as splinters of wood or metal).
1. Turn the clamping lever (13) as far to the left as
possible and hold it in this position.
2. Insert the saw blade in the chuck (16). Check
that the saw blade is securely fixed and that
the teeth are pointing in the cutting direction.
3. Let go of the clamping lever. Check whether
the back of the saw blade is positioned in the
centre of the guide roller (10). Make sure to
use the right sawblade for the corresponding
material. Included with the machine is a coarse
sawblade for wood and a fine sawblade for
metal and plastics.
Removing the saw blade
1. Turn the clamping lever (13) as far to the left as
possible and hold it in this position.
2. Remove the saw blade from the chuck (16).
3. Let go of the clamping lever.
Attaching the parallel guide
Fig. C
1. Loosen the bolts (14).
2. Mount the parallel guide (19) onto the
baseplate (9).
3. Set the desired cutting width using the scale
on the parallel guide (19) and the cutting mark
on the baseplate (9). The cutting mark (21)
indicates the position of the saw blade.
4. Tighten the bolts (14).
4. OPERATION
Switching the machine on/off
Fig. A
The on/off switch (2) is used for activating the
machine and adjusting speed.
•
To start the machine, press and hold the lockoff
button (1) and press the on/off switch (2).
• The further the on/off switch (2) is being
pushed, the faster the blade will move. The
required speeds depends on the material and
can be determined by practical testing.
• To stop the machine, release the on/off switch
(2).
Adjusting the bevel angle
Fig. A, D
1. Loosen the bolts (18), using the hex key (15).
2. Adjust the baseplate (9) to the desired position
(0°- 45°). The sawing angle (bevel) can be read
on the scale (7).
3. Tighten the bolts (18), using the hex key (15).
It is possible to store the hex key onto the
machine, as shown on Fig. A.
Adjusting the pendulum action
Fig. A
The pendulum action switch (6) is used to set the
way in which the teeth of the saw blade grip the
material. The pendulum action switch can be set
to 4 positions:
0 - No pendulum action
1 - Small pendulum action
2 - Medium pendulum action
3 - Large pendulum action
The required pendulum action can be determined
by practical testing, although the following
instructions can be observed:
• Soft material (wood, plastics etc.): set the
pendulum to level II or III. For a finer and
cleaner saw cut, use pendulum level 0 or I.
• Thin material, use pendulum level 0.
• Hard material (hardwood, steel etc.): set the
pendulum to level 0.
• Curves: set pendulum to level 0.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm JSM1033 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm JSM1033 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 5,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info