697791

Ferm JSM1023 Manual

8
Zoom out
Zoom in
Previous page
1/140
Next page
8
EN
teeth and select a lower speed.
- For soft materials, use a saw blade with coarse
teeth and select a higher speed.
Setting the mitre angle (fig. D)
The mitre angle is variable between 0° and 45°.
The mitre angle can be read from the scale (9).
Do not set the mitre angle during use.
• Slacken the Allen screws (18) using the Allen
key (12).
• Tilt the saw shoe (7) to the required position.
• Tighten the Allen screws (18) using the Allen
key (12).
Using the pendulum action switch (fig. A)
The pendulum action switch is used to set the
way in which the teeth of the saw blade grip the
material. The pendulum action switch can be set
to 4 positions.
Do not set the pendulum position during
use.
• Turn the pendulum action switch (4) to required
position according to the material to be
worked. Refer to the table below to select the
required position.
Material Pendulum position
Wood 1-3
Plastics 1
Aluminium 0-1
Steel 0
Ceramics 0
Rubber 0
Dust extraction (fig. E)
• Insert the dust extraction adapter (19) into the
dust extraction connection (10).
• Connect the hose of a vacuum cleaner to the
dust extraction adapter (19).
Hints for optimum use
• Clamp the workpiece. Use a clamping device
for small workpieces.
• Draw a line to define the direction in which to
guide the saw blade.
• Firmly hold the machine by the grip.
• Set the sawing speed.
• Set the mitre angle.
• Set the pendulum position.
• Switch on the machine.
• Wait until the machine has reached full speed.
• Place the saw shoe on the workpiece.
• Slowly move the machine along the pre-drawn
line, firmly pressing the saw shoe against the
workpiece.
• Do not apply too much pressure on the
machine. Let the machine do the work.
• Switch off the machine and wait for the
machine to come to a complete standstill
before putting the machine down.
CLEANING AND MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
mains plug from the mains.
• Regularly clean the housing with a soft cloth.
• Keep the ventilation slots free from dust and
dirt. If necessary, use a soft, moist cloth to
remove dust and dirt from the ventilation slots.
• Regularly clean the saw blade to avoid
inaccuracies during use.
• Regularly lubricate the guide roller.
Replacing the saw blade (fig. B)
Worn or damaged saw blades must be replaced
immediately.
Only use sharp and undamaged saw
blades.
• To remove the old saw blade (15), proceed
as described in the section „Mounting and
removing the saw blade“.
• To mount the new saw blade (15), proceed
as described in the section „Mounting and
removing the saw blade“.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm JSM1023 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm JSM1023 in the language / languages: All languages as an attachment in your email.

The manual is 15,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info