697791
7
Zoom out
Zoom in
Previous page
1/140
Next page
7
EN
8. Allen screw for parallel guide
9. Scale for mitre angle
10. Dust extraction connection
11. Grip
12. Allen key
13. Allen key holder
ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Mounting and removing the saw blade (fig. B)
Refer to the table below to select the required saw
blade.
Saw blade Material
Coarse Wood
Medium Wood
Fine Steel, aluminium, plastic
Very fine Wood (curves)
Do not attempt to remove the guard from
the machine.
Mounting
Raise the guard (5).
Slacken the Allen screws (14) using the Allen
key (12).
Insert the saw blade (15) in the saw blade
holder (6) as far as possible. The teeth of
the saw blade (15) must point upward and
forward. The smooth side of the saw blade
must engage in the slot of the guide roller (16).
Tighten the Allen screws (14) using the Allen
key (12).
Lower the guard (5).
Removing
Raise the guard (5).
Slacken the Allen screws (14) using the Allen
key (12).
Remove the saw blade (15) from the saw blade
holder (6).
Tighten the Allen screws (14) using the Allen
key (12).
Lower the guard (5).
Mounting and removing the parallel guide
(fig.C)
The parallel guide is used for sawing along edges
at a maximum distance of 16 cm.
Mounting
Slacken the Allen screws (8) using the Allen
key (12).
Insert the parallel guide (17) into the saw shoe
(7).
Set the parallel guide (17) to the required
position.
Tighten the Allen screws (8) using the Allen key
(12).
Removing
Slacken the Allen screws (8) using the Allen
key (12).
Remove the parallel guide (17) from the saw
shoe (7).
Tighten the Allen screws (8) using the Allen key
(12).
USE
Switching on and off (fig. A)
To switch on the machine, press the on/off
switch (1).
To switch the machine to continuous mode,
keep the on/off switch (1) pressed and
simultaneously press the lock-on button (2).
To switch off continuous mode, press the on/
off switch (1) again.
To switch off the machine, release the on/off
switch (1).
Setting the speed (fig. A)
The speed adjustment wheel is used for setting
the speed. The speed adjustment wheel can be
set to 6 positions. The ideal speed depends on
the profile and the teeth of the saw blade and on
the material to be worked.
Do not set the speed during use.
Turn the speed adjustment wheel (3) to the
required position.
- For hard materials, use a saw blade with fine
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm JSM1023 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm JSM1023 in the language / languages: All languages as an attachment in your email.

The manual is 15,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info