800223

Ferm HTM1008 Manual

10
Zoom out
Zoom in
Previous page
1/44
Next page
10
EN
hazards occurring to other people or their
property.
k) Do not operate the hedge trimmer when
barefoot or wearing open sandals, always
wear substantial footwear and long
trousers. The use of sturdy gloves, non-skid
footwear and safety glasses is recommended.
Do not wear loose clothing or jewelry which
can be caught in moving parts.
l) Thoroughly inspect the area where the
hedge trimmer is to be used and remove all
wires and other foreign objects.
m) Prior to operation, check cutter blades,
blade bolts and cutter assembly for wear or
damage. Do not operate with a damaged or
excessively worn cutting device.
n) Know how to stop the hedge trimmer
quickly in an emergency.
o) Cut a hedge only in daylight or in good
artificial light.
p) Never operate the hedge trimmer with
defective guards or without the guard in
place.
q) Never hold the hedge trimmer by the guard.
r) When operating the hedge trimmer, ensure
to keep proper footing and balance at all
times.
s) Always be aware of your surroundings and
stay alert for possible hazards that you
may not hear whilst operating the hedge
trimmer.
t) Keep all nuts, bolts and screws tight to
ensure that the hedge trimmer is always in
a safe working condition.
u) The hedge trimmer should be stored in a
dry, high or locked up place out of the reach
of children.
v) Replace worn or damaged parts for safety.
w) Do not attempt to repair the machine unless
you are qualified to do so.
x) Hold the product securely with both hands.
2. MACHINE INFORMATION
Intended use
The machine is intended for domestic use, for
cutting and trimming hedges and bushes at
elevated height, while the user is situated on the
ground. The machine is not intended to be used
on a ladder or steps. The machine is not designed
to cut grass and cannot be used as a grass
trimmer. This tool is not intended for commercial
or industrial use.
TECHNICAL SPECIFICATIONS
Model No. HTM1008
Rated voltage 20V
No load speed 1.200/min.
Cutting length 400mm
Cutting width 23mm
Weight 2.3 kg
Sound pressure level LPA 77.9 db (A), KpA=3 dB (A)
Sound power level LWA 87.8 db (A), KwA=3 dB (A)
Guaranteed LWA 91dB
Vibration value:
Front handle Ah 2.55 m/s2, K=1.5 m/s2
Rear handle Ah 2.48 m/s2, K=1.5 m/s2
Only use the following batteries of the AX-POWER
20V battery platform. Using any other batteries
could cause serious injury or damage the tool.
CDA1158 20V, 1.5Ah Lithium-Ion
CDA1154 20V, 2Ah Lithium-Ion
CDA1155 20V, 4Ah Lithium-Ion
The following charger of the can be used to
charge these batteries.
CDA1156 Charger adapter
CDA1157 Quick charger
The batteries of the AX-POWER 20V battery
platform are interchangeable with all the FERM
AX-POWER battery platform tools.
Vibration level
The vibration emission level stated in this
instruction manual has been measured in
accordance with a standardized test given in
EN 62841; it may be used to compare one tool
with another and as a preliminary assessment of
exposure to vibration when using the tool for the
applications mentioned.
• Using the tool for different applications, or with
different or poorly maintained accessories,
may significantly increase the exposure level.
• The times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm HTM1008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm HTM1008 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info