510087

Ferm HDM1021 Manual

6
Zoom out
Zoom in
Previous page
1/108
Next page
EN
6 Ferm
the chuck (4).
• Turn the auxiliary grip (7) to the required
position.
• Tighten the auxiliary grip (7) by turning it
clockwise.
Removing
• Loosen the auxiliary grip (7) by turning it
counterclockwise.
• Remove the auxiliary grip (7).
• Tighten the auxiliary grip (7) by turning it
clockwise.
Mounting and removing the depth stop
(fig. C)
Mounting
• Loosen the auxiliary grip (7) by turning it
counterclockwise.
• Insert the depth stop (8) through the hole in
the auxiliary grip (7).
• Set the depth stop (8) to the required position.
• Tighten the auxiliary grip (7) by turning it
clockwise.
Removing
• Loosen the auxiliary grip (7) by turning it
counterclockwise.
• Remove the depth stop (8).
• Tighten the auxiliary grip (7) by turning it
clockwise.
Mounting and removing the dust collector
(fig. D)
The dust collector prevents dust from entering the
machine when drilling into ceilings.
Immediately replace a damaged dust
collector.
Mounting
• If necessary, remove the accessory from the
chuck (4).
• Slide the dust collector (15) over the shaft of
the accessory.
• Insert the accessory with the dust collector
(15) into the chuck (4).
Removing
• Remove the accessory with the dust collector
(15) from the chuck (4).
• Remove the dust collector (15) from the
accessory.
Use
Switching on and off
(fig. A)
• To switch on the machine, press the on/off
switch (1).
• To switch off the machine, release the on/off
switch (1).
Setting the operating mode
(fig. A & E)
The drill selection switch and the hammer
selection lever must be set according to the
required operating mode. Refer to the table below
to set the required operating mode.
Setting (fig. E) Operating mode
A Demolition hammer / Chisel
B Hammer drill
C Drill
• Turn the drill selection switch (2) and the
hammer selection lever (3) to the required
position.
Speed Preselection
The required speed can be preselected with the
thumbwheel. Also during running the rotational
speed can be adjusted.
1 – 2 = low speed
3 – 4 = medium speed
5 – 6 = high speed
Max = maximum speed
The required speeds depends on the material and
can be determined by practical testing.
Hints for optimum use
• Clamp the workpiece. Use a clamping device
for small workpieces.
• Firmly hold the machine by the grip.
• Set the operating mode.
• Switch on the machine.
• Do not apply too much pressure on the
machine. Let the machine do the work.
• Switch off the machine and wait for the
machine to come to a complete standstill
before putting the machine down.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm HDM1021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm HDM1021 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info