510087
5
Zoom out
Zoom in
Previous page
1/108
Next page
EN
5
Ferm
connected to the terminal which is marked
with the letter N or coloured black.
• The wire which is coloured brown must be
connected to the terminal which is marked
with the letter L or coloured red.
Technical data
Mains voltage 220-240V~
Mains frequency 50Hz
Power input 1,500W
No-load speed 350 - 800 /min
Impact rate 1100 - 2700 /min
Max. drilling diameter
Wood 40 mm
Steel 13 mm
Concrete 36 mm
Weight 6 kg
Noise and vibration
Hammer position
Sound pressure (Lpa) 98.5 dB(A)
Acoustic power (Lwa) 109.5 dB(A)
Uncertainty (K) 3 dB(A)
Vibration main handle 19.819 m/s
2
Uncertainty (K) 1.5 m/s
2
Hammer/drill position
Sound pressure (Lpa) 96.88 dB(A)
Acoustic power (Lwa) 107.88 dB(A)
Uncertainty (K) 3 dB(A)
Vibration main handle 24.847 m/s
2
Uncertainty (K) 1.5 m/s
2
Wear hearing protection.
Vibration level
The vibration emission level stated in this
instruction manual has been measured in
accordance with a standardised test given in EN
60745; it may be used to compare one tool with
another and as a preliminary assessment of
exposure to vibration when using the tool for the
applications mentioned
• using the tool for different applications, or with
different or poorly maintainted accessories,
may significantly increase the exposure level
• the times when the tool is switched off or when
it is running but not actually doing the job, may
signifi cantly reduce the exposure level
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
Description
(fig. A)
Your hammer drill has been designed for drilling
holes into wood, steel, and masonry. The machine
can also be used as a demolition hammer in
combination with the SDS chisels.
1. On/off switch
2. Drill selection switch
3. Hammer selection lever
4. Chuck
5. Locking sleeve
6. Main grip
7. Auxiliary grip
8. Depth stop
9. Lubrication point
10. Carbon brush holder
11. Adjusting wheel for electronic speed control
Assembly
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Mounting and removing the accessory
(fig. B)
Do not use blunt drill bits or chisels.
Immediately sharpen or replace blunt drill
bits or chisels.
Mounting
• Apply a few drops of oil to the shaft of the
accessory.
• Slide the locking sleeve (5) to the rear.
• Insert the accessory into the chuck (4).
• Secure the accessory by turning it
counterclockwise until it locks into place.
• Release the locking sleeve (5).
Removing
• Slide the locking sleeve (5) to the rear.
• Remove the accessory from the chuck (4).
• Release the locking sleeve (5).
Mounting and removing the auxiliary grip
(fig. C)
Mounting
• Loosen the auxiliary grip (7) by turning it
counterclockwise.
• Mount the auxiliary grip (7) by sliding it over
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm HDM1021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm HDM1021 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info