Manual Ferm FRS-710 (page 5 of 52) (English, German, Dutch, Danish, French, Italian, Norwegian)

110232

Zoom out

Zoom in

1/52

Ferm 5

• Thestrokeraterequireddependsuponthe

material conditions. The optimal setting

should be determined in use.

• Afterworkingforlongerperiodsatlow

speed you should allow the machine to cool

down by running it at maximum speed with

no-load for approx. 3 minutes.

ADJUSTING THE FOOT PLATE ANGLE

Fig.D

• Toallowthefootplatetofollowand

securely rest on the workpiece, the angle of

the footplate can be adjusted as shown in

the diagram.

• Thefootplatecanalsobeextended

by loosening the two footplate length

adjustment screws (Fig. A8) using the 4 mm

hexagon key and then pulling the footplate

out to the required length.

Ensure the footplate adjustment

screws are secure before resuming

work.

SAWING TIPS

• Adjustsawbladeandstrokeratetosuitthe

material to be processed. For right radius

curves it is best to use a narrow saw blade.

Apply coolant or lubricant to deal with the

beat produced along the cut line when

sawing metal.

• Checkwood,chipboards,building

materials etc, for foreign bodies (nails,

screws etc.), before sawing and remove

them, if necessary.

• Clampmaterialwell.Donotsupportthe

workpiecewithhandorfoot.Donottouch

objects or the floor with the saw running

(danger of backlash).

• Materialcontainingasbestosmustnotbe

sawn!

• Putthefootplateonthesurfaceofthe

workpiece, and saw through it with constant

contactpressureorfeed.Ifthesawblade

seizes switch the machine off immediately .

Spread the gap with a suitable tool and pull

out the saw blade.

• Afterfinishingwork,switchoffthemachine

and only put down after it has come to a

complete standstill.

PLUNGE CUTTING

Fig.E

• Plungecuttingmayonlybeusedonsoft

materials such as wood, aerated concrete,

gypsum plaster boards, etc.

• However,thisrequiresacertainpractise

and is only possible with short saw blades.

• Placethesawontotheworkpieceand

switch it on.

• Ensurethatthebottomedgeofthefootplate

rests on the workpiece surface as shown.

• Slowlysawintotheworkpieceatanangle,

moving the saw to a vertical position and

continue to saw along the cutting line.

• Switchthesawoffandliftofftheworkpiece

when the work is complete.

FLUSH SAWING

• Elasticbi-metalsawbladesallowyouto

saw projecting objects (e,g, water pipes,

iron bars, etc,) flush against the wall.

• Applythesawbladedirectlytothewall

and bend slightly so that the footplate rests

against the wall.

• Switchthemachineonandsawoffthe

workpiece keeping constant lateral pressure

against the wall.

There are no user servicable parts in this unit.

Any repairs or servicing should be carried out

by qualified service en-gineers.

TROUBLESHOOTING

Incasethemachinedoesnotworkwell,we

give you some possible causes and solutions.

1. The electromotor gets hot

• Thecoolventilationslotsinthemotorare

stopped up with dirt.

Clean the cool ventilation slots.

• Themotorisdefect.

Have your machine repaired or checked

by your local Ferm dealer.

2. The connected machine does not work

• Interruptioninthemainsconnection.

Check mains connection for fracture.

Have your machine repaired/checked

by your local Ferm dealer.

RSM1011 Ma # 0810-10.1 FC.indd 5 10/10/08 4:59:42 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FRS-710 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 3,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FRS-710 Manual

Product: