110232

Ferm FRS-710 Manual

4
Zoom out
Zoom in
Previous page
1/52
Next page
Ferm4
GB
• Alwaysremovetheplugfromthemains
socket before carrying out any work on the
machine.
• Donotcarrythemachinebythecable.
• Incorrecthandlingmaydamagethe
machine. Therefore always comply with the
following instructions.
• Useonlysharpsawbladesinperfect
condition; replace cracked, distorted or
blunt saw blades immediately.
• Machineshouldonlybeswitchedonwith
blade installed
• Selecttools,strokerateandpendulum
actions according to material, Take care to
maintain a constant reed rate.
• Donotattempttostopthesawbladewith
lateral pressure after switching off.
• Onlyusegenuineaccessories.
• Alwaysusethecorrectsupplyvoltage.The
voltage specifications on the rating plate
must correspond with the mains voltage.
Equipmentmarkedwith230Vcanalsobe
connected to 220-240 V.
IMMEDIATELY SWITCH OFF THE MACHINE
WHEN:
• Excessivesparkingofthecarbonbrushes
and verticiliosis in the collector.
• Interruptioninthemainsplug,mainsleador
mains lead damage.
• Defectswitch.
• Smokeorstenchofscorchedinsulation.
ELECTRICAL SAFETY
Always check that the power supply
corresponds to the voltage on the
rating plate.
Your machine is double insulated in
accordance with EN 50144; therefore
no earthwire is required.
Replacing cables or plugs
Immediatelythrowawayoldcablesorplugs
whentheyhavebeenreplacedbynewones.It
is dangerous to insert the plug of a loose cable
in the wall outlet.
Using extension cables
Onlyuseanapprovedextensioncablesuitable
for the power input of the machine. The
minimum conductor size is 1.5 mm
2
.
When using a cable reel always unwind the reel
completely.
OPERATION
CHANGING/FITTING THE BLADE
Fig.B
Ensure the machine is unplugged.
• Loosenthegrubscrewwiththe3mm
hexagon key.
• Insertthesawbladebetweenthestrokerod
and the clamping plate.
• Takecarethatthesecuringpinofthe
stroke rod engages in the hole of the saw
blade. (Saw blade can not be pulled out).
• Retightenthegrubscrew.
• Whenchangingthesawblade,takecare
that the blade holder is free of material
residue (e.g. wood or metal shavings),
• Beforeusingthesawmakesurethesaw
blade is secure.
USE
Fig.C
Make sure that the saw blade does not
rest on or touch any objects when the
machine is switched on.
Switching on
• Puttheon-offtriggerswitch(4).
Switching off
• Releasetheon-offtriggerswitch.
• Theon-offtriggerswitchcanbelockedon
for continuous operation by pressing the
trigger lock button whilst pulling the trigger.
• Toreleasethetriggerlock,simplypullthe
trigger switch again.
SPEED CONTROL
• Duringoperationandwhilstthemachine
is at rest the stroke rate (speed) can be
selected using the thumbwheel (5). The
stroke rate will remain constant even under
load.
RSM1011 Ma # 0810-10.1 FC.indd 4 10/10/08 4:59:41 PM
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FRS-710 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FRS-710 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info