Manual Ferm fpd 13 500 (page 6 of 22) (English, German, Dutch, French, Italian)

386213

Zoom out

Zoom in

1/22

Ferm 39

Ved at trykke trækomskifter (A) mere eller

mindre dybt ind kan hastigheden så reguleres

trinsløst.

Indstilling af den maksimale

omdrejningshastighed

• Tænd for maskinen (kontakt (A));

• Bloker kontakten (knap (B));

• Drej på det lille hjul (C) for at indstille den

ønskede maksimale omdrejningshastighed.

Omskiftning af rotationsretning

• For venstrerotation: skub kontakten (D) til “L”;

• For højrerotation: skub kontakten (D) til “R”.

Omskiftning normal boring/slagboring

Fig.E

Kontakten oven på borehammer er beregnet til

indstilling af almindelig boring eller slagboring:

• Tryk kontakten mod “bor” symbolet for

almindelig boring;

• Tryk kontakten mod “hammer” symbolet for

slagboring.

5. SERVICE &

VEDLIGEHOLDELSE

Sørg for at maskinen ikke står under

strøm, når der udføres

vedligeholdelsesarbejder på

mekanikken.

Maskinerne er udviklet til at fungere længe uden

problemer med et minimum af vedligeholdelse.

Ved at rengøre maskinen regelmæssigt og

behandle den korrekt, bidrager De til en længere

levetid for maskinen.

Driftsfeyl

Hvis Borehammer ikke funktionerer

tilfredsstillende, gives nedenfor eventuelle

årsager og afhjælpning.

1. Udsædvanlig mange gnister

• Dette tyder næsten altid på tilstedeværelse af

smuds i motoren eller på opslidte kulbørster.

• Kontakt venligst serviceadressen på

garantibeviset.

2. Borehammer bliver for varm

• Borehammer belastes for meget.

• Brug maskinen til det, den er beregnet til.

• Udskift boret med et skarpere bor.

• Motoren er defekt.

• Kontakt venligst serviceadressen på

garantibeviset.

Rengøring

Rengør regelmæssigt maskinkappen med en

blød klud, helst efter hvert brug. Sørg for at

ventilationshullerne er fri for støv og snavs. Brug

en blød klud, der er vædet i sæbevand til at

fjerne hårdnakket snavs. Brug ingen

opløsningsmidler, så som benzin, alkohol,

ammoniak, osv. Den slags stoffer beskadiger

kunststofdelene.

Smøring

Maskinen behøver ingen ekstra smøring.

Fejl

Skulle en fejl opstå, f.eks. pga. slidtage af en

enhed, kontakt venligst serviceadressen på

garantibeviset. På bagsiden af denne manual

finder du en tegning med alle dele, der kan

bestilles.

Miljø

For at undgå transportbeskadigelse leveres

maskinen i en solid emballage. Emballagen er så

vidt muligt lavet af genbrugsmateriale. Genbrug

derfor emballagen.

Defekte og/eller kasserede elektriske

eller elektroniske maskiner skal

afleveres på en genbrugsplads.

Garanti

Garantibetingelser er beskrevet på det separat

vedlagte garantibevis.

06 Ferm

Adjusting of the maximum rotation speed

• Switch the machine on by pressing

triggerswitch (A).

• Lock the triggerswitch (A) by pressing knob (B).

• Adjust the speed by turning the small wheel

Switching the direction of rotation

• Direction of rotation counter-clockwise: shift

switch (D) to “L”.

• Direction of rotation clockwise: shift switch (D)

to “R”.

Switch for percussion drilling

Fig.E

With the switch on top of the machine you can

select normal or percussion drilling:

• Slide the switch to the “Drill” symbol for

normal drilling.

• Slide the switch to the “Hammer” symbol for

percussion drilling.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

These machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Malfunction

Below we have listed a number of possible

causes and corresponding solutions in case the

machine does not function as it should:

1. Excessive sparkling

• This usely indicates dirt in the motor or

worndown carbon brushes.

• Please contact the service address on the

warranty card.

2. The percussion drill is overheating

• The ventilationslots are covered with dirt.

Clean them with a dry cloth.

• The percussion drill is overloaded.

• Use the machine for work for which it is

ment to be.

• Replace the drill for a sharp one or

sharpen the drill by using a benchgrinder

and a twist drill grinding attachment.

• The motor is defect.

• Please contact the service address on the

warranty card.

Cleaning

Regularly clean the machine housing with a soft

cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt. If the dirt

does not come off use a soft cloth moistened

with soapy water. Never use solvents such as

petrol, alcohol, ammonia water, etc. These

solvents may damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card. In the back of this manual you find

an exploded view showing the parts that can be

ordered.

Environment

To prevent damage during transport, the

appliance is delivered in a solid packaging which

consists largely of reusable material. Therefore

please make use of options for recycling the

packaging.

Faulty and/or discarded electrical or

electronic apparatus have to be

collected at the appropriate recycling

locations.

Warranty

The warranty conditions can be found on the

separately enclosed warranty card.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fpd 13 500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 3,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm fpd 13 500 Manual

Product: