389403
5
Zoom out
Zoom in
Previous page
1/22
Next page
DK
40 Ferm
Levetiden kan forlænges, hvis maskinen rengøres
regelmæssigt og håndteres korrekt.
Fejl
For det tilfælde, at maskinen ikke fungerer korrekt,
er herunder angivet en række mulige årsager med
tilhørende løsningsforslag:
1. Den elektroniske motor bliver varm
Rengør ventilationsåbningen
2. Støvet bliver ikke opsamlet
Støvposen er fuld / tøm støvposen
3. Slibepapiret er fyldt med klæbestof/maling
eller lignene materiale
Maling eller klæbestof er ikke tørt.
Nogle former for maling klæber mere til
slibepapir end andre / rengør ofte slibepapiret
Reparationer må udelukkende udføres
af en autoriseret installatør eller et
autoriseret serviceværksted.
Rengøring
Rengør regelmæssigt maskinkappen med en
blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs.
Brug en blød klud, der er vædet i sæbevand
til at fjerne hårdnakket snavs. Brug ingen
opløsningsmidler, så som benzin, alkohol,
ammoniak, osv. Den slags stoffer beskadiger
kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en
enhed, kontakt venligst serviceadressen på
garantibeviset. Seperat finder du en tegning med
alle dele, der kan bestilles.
Miljø
For at undgå transportbeskadigelse leveres
maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug
derfor emballagen.
Defekte og/eller kasserede elektriske
eller elektroniske maskiner skal
afleveres på en genbrugsplads.
Garanti
Læs det separat vedlagte garantikort for
garantibetingelserne.
GB
5Ferm
Before replacing the sanding sole
disconnect the sander from the mains.
Remove the sandpaper of the sole.
Remove the screws which the sole is fixed to
the sander.
Remove the sole.
Install the new sole on the sander.
Tighten the screws well.
4. USE
Operation
Push in the on/off switch (1) to start the
machine.
By adjusting the adjusting wheel (10) you can
regulate the speed.
The ventilating apertures (6) on the housing
must remain clear to ensure optimum cooling
of the motor.
Move the sander over the surface of your
workpiece.
Prevent pushing too much on the
machine during sanding. Excessive
sanding pressure does not lead to
increased sanding capacity, but
increases wear of the machine and the
sandpaper.
Grips
The sander is equipped with two grips: a handle
at the front side and one on the back side. Always
hold the sander with both hands on the handles,
so as to gain the best possible control over your
sanding operations. Besides you do not risk to
become in touch with the moving parts.
User tips
Apply long uniform movements to your sander
to obtain the best possible results.
The surface quality after sanding is determined
by the selected grain.
5. SERVICE & MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
This machine has been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Malfunction
Should the machine fail to function correctly, a
number of possible causes and the appropriate
solutions are given below:
1. The electromotor gets hot
Clean the ventilating apertures
2. The dust is not extracted
The dust bag is full / empty the dust bag
3. The abrasive paper is filled with adhesive/
paint or a similar material
Paint or adhesive is not really dry.
Some paints stick more to the abrasive paper
than others / clean the abrasive paper at
regular intervals
Repairs and servicing should only be
carried out by a qualified technician or
service firm.
Cleaning
Keep the ventilation slots of the machine clean to
prevent overheating of the engine. Regularly clean
the machine housing with a soft cloth, preferably
after each use. Keep the ventilation slots free from
dust and dirt. If the dirt does not come off use a
soft cloth moistened with soapy water. Never use
solvents such as petrol, alcohol, ammonia water,
etc. These solvents may damage the plastic parts.
Lubrication
The machine requires no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part,
please contact the service address on the
warranty card. Separately you will find an
exploded view showing the parts that can be
ordered.
Environment
To prevent damage during transport, the appliance
is delivered in a solid packaging which consists
largely of reusable material. Therefore please
make use of options for recycling the packaging.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm fos-180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fos-180 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info