389403

Ferm fos-180 Manual

4
Zoom out
Zoom in
Previous page
1/22
Next page
GB
4 Ferm
Interruption of the mains plug, mains lead or •
mains lead damage.
Defect switch•
Smoke or stench of scorched isolation•
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class II machine – Double insulation –
You don’t need any earthed plug.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in the
wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1,5 mm
2
. When using a cable
reel always unwind the reel completely.
3. ASSEMBLY
Prior to mounting an accessory always
unplug the tool.
Dust collection
Fig. 2
The sander has been carried out with a dust bag
(3) to keep the working surface clean. The dust
bag must be installed on the back side of the
machine, on the opening. It is necessary to empty
the dust bag regularly for an efficient use.
Empty it as follows:
Turn the dust bag slightly and pull it out of the •
machine’s adapter.
Empty the dust bag in a suitable place.•
Push the dust bag on to the machine’s adapter •
till it locks into place.
Remember that the dust extraction only
works when using perforated
sandpaper.
Replacing worn sanding paper
Fig. 3
Before assembly sanding paper always
remove the plug from the mains.
Replacing worn sanding paper
This machine is suitable for Velco
®
sanding paper
and universal sanding paper.
Before assembly sanding paper always
remove the plug from the mains.
Velcro
®
sanding paper (189 x 92 mm)
The sandpaper is fixed by Velcro
®
fastener to
facilitate the replacement.
Simply pull off the sanding paper.•
Press the new one in the centre of the sanding •
sole.
Universal sanding paper (240 x 92 mm)
Fig. 3
The sanding machine is provided with a rectangle
sanding sole. By tightening the sandpaper it does
not wear out so fast, so it will wear well longer.
Open the back paper clamp (4) by pulling the •
handle (5) up.
Install the sandpaper under the clamp. Put the •
paper in the middle of the sanding sole and
look after the perforations in the paper. They
have to correspond with those on the sanding
sole, so that the dust can be exhausted.
Push the handle back into its original position.•
Repeat the operation to fix the sand-paper on •
the front side.
Fix the sandpaper as tight as possible.•
Coarse sand-paper (grain 50) removes in general
the bigger part of the material and fine sand-paper
(grain 120) is used for the finishing.
Replacing the sanding sole
The sole has to be replaced when the Velcro has
been worn out.
41Ferm
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm fos-180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fos-180 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info