Manual Ferm fjs 750 l (page 11 of 60) (English, German, Dutch, French, Italian)

382948

Zoom out

Zoom in

1/60

Ferm 11

Cutting in

Fig. 9

If the starting position of the workpiece to be sawn is not the side, or if no hole has been

drilled, you must cut in. To do this, proceed as follows:

• Put the jigsaw on the rounded front of the bottom plate .

• Switch on the appliance and slowly lower the jigsaw until it touches the workpiece.

• Let the jigsaw cut into the workpiece gently without forcing it.

• When you are through the workpiece, take the jigsaw out of the hole.

• Place the appliance in the normal position in the sawn hole and continue the saw cut.

You can also cut in by first drilling a hole in the workpiece. To do this, use a bit that makes

a hole big enough for the saw blade. Now you can carry out the steps described under

'Sawing'.

5. MAINTENANCE

During maintenance and cleaning always remove the mains plug from the

socket. Never use liquids when cleaning electrical parts of the jigsaw.

Maintain the jigsaw regularly to prevent unnecessary problems. This will ensure that your

appliance remains in optimum condition.

• Keep the bottom plate clean so that no inaccuracies occur during sawing.

• Keep the outside of the jigsaw clean so that all moving parts can move accurately

and without wear.

• Keep the ventilation slots of the motor clean so that these do not overheat.

• If the carbon brushes are worn the jigsaw will run noisily and unevenly. In the end the

jigsaw will no longer work. Have the carbon brushes replaced by an authorized

service centre.

• Lubricate the saw blade guide regularly.

Malfunctions

• The electric motor is

getting hot.

• The appliance does not

work.

• The motor is being

overloaded by workpieces

that are too big.

• The motor is defective.

• The mains connection has

been broken.

• The switch is damaged.

• Saw at a lower speed so

that the motor can cool

down.

• Contact the service

address on the warranty

card.

• Check the power cord for

damage.

• Contact the service

address on the warranty

card.

110 Ferm

C. Drej pladen til højre eller venstre i den ønskede savvinkel. De kan aflæse vinklen på

vinkelmåleren (13). Den største savvinkel er 45º.

D. Tryk bundpladen fremad igen for at låse den.

E. Stram umbrakoskruerne (12) til igen.

4. BETJENINGEN

Fastlåsning af afbryderen

Fig. 4

Tryk afbryderen ind for at starte stiksaven. Afbryderen kan låses fast med låseknappen.

Det gøres som følger:

A. Tryk afbryderen ind.

B. Hold afbryderen trykket ind mens De trykker låseknappen ind. Stiksaven vil nu køre

kontinuerligt.

Udløs låsemekanismen ved at trykke på afbryderen igen.

Hastighedskontrol

Fig. 5

Savens hastighed kan indstilles med drejeknappen øverst på stiksaven. Jo højere

indstilling, jo højere er hastigheden. Den højeste indstilling er 6. Den ideelle savhastighed

afhænger af profilen og tænderne på saven samt det materiale De vil save i. Til bløde

materialer, vælg en rimelig høj hastighed og en grovtandet sav. Hvis De vil save hårde

materialer vælg en lavere hastighed og en fintandet sav.

Indstilling af pendul

Fig. 1+6

For at opnå det bedste savresultat, skal De indstille den måde savens tænder griber

materialet på. Dette gør De ved at indstille pendulet (8).

• Bløde materialer (træ, plastik o.s.v.): sæt pendulet på niveau II eller III. For et skarpt

savsnit, sæt pendulet på niveau 0 eller I.

• Mellemhårde materialer (løvtræ, aluminium o.s.v.): indstil pendulet afhængigt af

forholdene. Til tynde materialer brug niveau 0, eller I hvis De arbejder med knive eller

raspe.

• Hårde materialer (stål o.s.v.): sæt pendulet på niveau 0.

• Kurver: sæt pendulet på niveau 0.

De kan indstille pendulets niveau mens maskinen arbejder.

Støvopsamling

Fig. 7

For at holde overfladen fri for støv, er stiksaven udstyret med en tilslutning til en

støvfjerner. De kan sætte Deres støvsuger til på denne tilslutning. Brug den adapter til

støvsugeren der er leveret med til dette.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fjs 750 l in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 26,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm fjs 750 l Manual

Product: