Manual Ferm FDCS 720 L (page 6 of 124) (English, German, Dutch, Danish, French, Italian, Norwegian)

79265

Zoom out

Zoom in

1/124

Replacing cables or plugs

Immediately throw away old cables or plugs when

they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

• The tool is suitable for use as a screwdriver

and drill. Any other application is specically

excluded.

3. MOUNTING ACCESSORIES

Inserting and removing bits

Fig. 1

In addition to screwdriver bits with a hexagonal

shaft, this tool can also accommodate drill bits

with a hexagonal shaft.

Always use short screwdriver bits in

combination with the magnetic bit holder.

The 50 mm screwdriver bits can be used

without the magnetic bit holder.

• Pull back the locking sleeve (2) and insert the

magnetic bit holder or 50mm screwdriver bit.

• Release the locking sleeve.

• To remove, pull back the locking sleeve and

remove the bit or magnetic bit holder.

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Hold the appliance rmly and press the

screwdriver steadily onto the work piece. Do not

overload the appliance. Only use bits with no

visible wear. Worn bits will have a bad effect on

the functioning of the appliance.

Adjusting the torque

Fig. 1

The appliance has 17 different torque settings

with which to set the power for driving and

removing screws.

• Set the torque settings ring (3) to the desired

position. The available torque settings are

indicated on the settings ring by the numbers 1

to 15 and by dots between the gures to

dene intermediate settings. And a setting for

drilling indicated by the drill icon (17 in total).

• You should preferably choose a setting as low

as possible when using the screwdriver. Select

a higher setting if the motor slips.

Driving and removing screws

Fig. 1

• Set the direction switch (9) to position ‘’ in

order to drive screws.

• Set the direction switch (9) to position ‘’ in

order to remove screws.

Ensure that the direction switch (9) is

always set to ‘’ during drilling and the

drill symbol selected on the torque

settings ring.

Switching the device on and off

Fig. 1

• Depress the on/off switch (8). It regulates the

speed of the appliance by transmitting power

to the switch.

• Release the on/off switch (8) to halt the drill

chuck immediately, it will no longer run on.

• Move the direction reversing switch (9) to the

centre in order to lock the appliance in its

disabled state.

The tool will turn at its slowest speed when the

switch is depressed lightly. The tool will turn at its

fastest speed when the trigger is fully depressed.

Only lay down the appliance when it has stopped

running completely. Do not place it on a dusty

surface as particles of dust could get into the

mechanism.

LED work light

Fig. 2

• Press the LED work light switch (11) once to

switch the LED work light on.

• Press the LED work light switch (11) again to

switch the LED work light off.

Charging the battery

• Only use the battery charger in a temperature

range between + 5 °C to + 40 ºC.

• Only use the battery charger in dry, ventilated

rooms.

One advantage of using Lithium-Ion batteries is

that, until the battery is almost empty, hardly any

power fading is noticeable. The machine can be

used until you start noticing that the power of the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FDCS 720 L in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 22,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FDCS 720 L Manual

Product: