78516

Ferm FDAG 880 Manual

7
Zoom out
Zoom in
Previous page
1/108
Next page
7
EN
Mains plug replacement (UK only)
If the moulded 3-pin plug attached to the unit is
damaged and needs replacing, it is important that
it is correctly destroyed and replaced by an
approved BS 1363/5A fused plug and that the
following wiring instructions are followed.
The wires in the mains cable are coloured in
accordance with the following code:
blue neutral
brown live
As the colours of the wires in the mains cable of
the unit may not correspond to the coloured
markings identifying the terminals in the plug,
proceed as follows:
- The wire which is coloured blue must be
connected to the terminal which is marked with
the letter N or coloured black.
- The wire which is coloured brown must be
connected to the terminal which is marked with
the letter L or coloured red.
TECHNICAL DATA
AGM1043
Mains voltage V~ 230
Mains frequency Hz 50
Power input W 880
No-load speed min
-1
11,000
Grinding disc
Diameter mm 125
Bore mm 22.2
Spindle thread M14
Weight kg 2.2
NOISE AND VIBRATION
AGM1043
Sound pressure (L
pa
) dB(A) 87.7
Acoustic power (L
wa
) dB(A) 98.7
Uncertainty (K) dB(A) 3
Vibration m/s
2
7.52
Uncertainty (K) m/s
2
1.5
2
Wear hearing protection.
Vibration level
The vibration emission level stated in this instruction
manual has been measured in accordance with a
standardised test given in EN 60745; it may be used
to compare one tool with another and as a
preliminary assessment of exposure to vibration
when using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories,
may signicantly increase the exposure level
- the times when the tool is switched off or when
it is running but not actually doing the job, may
signicantly reduce the exposure level
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
DESCRIPTION (FIG. A)
Your angle grinder has been designed for grinding
and cutting masonry and steel.
1. On/off switch
2. On/off switch lock
3. Spindle lock button
4. Spindle
5. Guard
6. Main grip
7. Auxiliary grip
8. Carbon brush indicator
ASSEMBLY
4
Before assembly, always switch off the
machine and remove the mains plug
from the mains.
Mounting and removing the grinding disc

2
Never attempt to remove the guard.
Mounting
● Place the machine on a table with the guard
(5) facing upwards.
● Mount the spacer (9) onto the spindle (4).
● Mount the grinding disc (10) onto the spindle (4).
● Keep the spindle lock button (3) pressed and
rmly tighten the tension nut (11) using the
spanner (12).
Removing
● Place the machine on a table with the guard
(5) facing upwards.
● Keep the spindle lock button (3) pressed and
loosen the tension nut (11) using the spanner
(12).
● Remove the grinding disc (10) from the spindle
(4).
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FDAG 880 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FDAG 880 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Norwegian as an attachment in your email.

The manual is 5,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info