78516

Ferm FDAG 880 Manual

6
Zoom out
Zoom in
Previous page
1/108
Next page
6
EN
Make sure that the user is protected from the
grinding disc as much as possible.
● Make sure that the workpiece is properly
supported or xed.
● Wear safety goggles. Wear hearing protection.
Wear a dust mask. If necessary, use other
protective means, such as safety gloves,
safety shoes, etc. Risk of personal injury.
● Keep bystanders away from the work area.
Make sure that all persons in the work area
wear protective equipment. Risk of personal
injury.
● Keep the mains cable away from the rotating
grinding disc. If the mains cable touches the
rotating grinding disc, your hands or arms may
come in contact with the grinding disc.
Risk of personal injury.
● Hold the machine by the insulated gripping
surfaces where the grinding disc may contact
hidden wiring or the mains cable. If the
grinding disc contacts a ‘live’ wire, the exposed
metal parts of the machine can also become
‘live’. Risk of electric shock.
● Do not use the machine while carrying it at
your side. Risk of personal injury.
● Do not use the machine on workpieces
requiring a maximum grinding depth that
exceeds the maximum grinding depth of the
grinding disc.
● Do not use accessories that require liquid
coolants. Risk of electric shock.
● Do not use the machine near ammable
materials. Risk of re.
● Do not work materials containing asbestos.
Asbestos is considered carcinogenic.
● Do not work metal with a magnesium content
of more than 80%.
● Beware that the grinding disc continues to
rotate for a short period after switching off the
machine. Do not attempt to bring the grinding
disc to a standstill yourself.
● Never put the machine down on a table or a
workbench before it has been switched off.
● Regularly clean the ventilation slots. Risk of
electric shock.
Kickback is a sudden reaction to a pinched,
bound or twisted grinding disc, which causes the
machine to lift up and out of the workpiece towards
the user. If the grinding disc is pinched or bound
tightly by the cut, the grinding disc jams and the
machine is rapidly driven back towards the user.
If the grinding disc is twisted in the cut, the back
edge of the grinding disc can dig into the top
surface of the workpiece, which causes the
grinding disc to climb out of the cut and jump
back towards the user.
Kickback is the result of incorrect use of the
machine and/or incorrect operating procedures or
conditions. Kickback can be avoided by taking
proper precautions:
● Firmly hold the machine with both hands.
Position your arms to resist kickback forces.
Position your body to either side of the grinding
disc, but not in line with the grinding disc.
Kickback can cause the grinding disc to jump
backwards. If proper precautions are taken,
kickback forces can be controlled by the user.
● Be extra careful when using the machine on
corners, sharp edges, etc. Make sure that the
grinding disc does not become jammed.
Risk of kickback.
● If the grinding disc jams or if you interrupt a cut
for any reason, release the on/off switch and
hold the machine motionless in the material
until the grinding disc comes to a complete
standstill. Never attempt to remove the
machine from the workpiece or pull the
machine backward while the grinding disc is in
motion. Risk of kickback.
● Do not use blunt or damaged grinding discs.
Unsharpened or incorrectly mounted grinding
discs produce narrow cuts, which causes
excessive friction and kickback and increases
the risk of the grinding discs becoming
jammed.
● Do not use toothed saw blades. Do not use
woodcarving blades for saw chains. Risk of
personal injury.
ELECTRICAL SAFETY
3
Always check that the voltage of the
power supply corresponds to the voltage
on the rating plate.
● Do not use the machine if the mains cable or
the mains plug is damaged.
● Only use extension cables that are suitable for
the power rating of the machine with a
minimum thickness of 1.5 mm
2
. If you use a
extension cable reel, always fully unroll the
cable.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FDAG 880 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FDAG 880 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Norwegian as an attachment in your email.

The manual is 5,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info