79094

Ferm FDAG 750 Manual

6
Zoom out
Zoom in
Previous page
1/52
Next page
GB
6
Ferm
Fasten the side handle for left-hand operation •
on the right-hand side of the machine.
Fasten the side handle for right-hand operation •
on the left-hand side of the machine.
Make sure that the side handle is
fastened properly and cannot loosen
unexpectedly.
Mounting the guard
Fig. 2
Mount the guard before using the machine.
Assembly
Place the guard (2) on the housing. Be aware •
that the notch of the guard falls across the edge
of the housing.
Place the fixing-ring (7+12) on the guard: the •
ring-holes have to be on the screw-holes.
Mount the guard en fixing-ring with help of the •
4 screws and washers (8).
The closed side of the guard always has to •
point in the user’s direction.
Be aware the screws are tightened well
enough. Check regularly if the screws
are still fixed.
Disassembly
Remove the flange nut and the grinding disc •
with lower flange from the spindle.
Unscrew the 4 screws (with washers) en •
remove the fixing-ring.
Remove the guard from the machine.•
•
Mounting a grinding disc
Fig. 3
Use grinding discs of the correct dimension. Use
fibre reinforced grinding discs only. The grinding
disc must not touch the edge of the guard.
Remove the plug from the mains
Press the spindle lock (Fig. 1 - 5) and turn the •
spindle (6) until it engages in the lock. Keep the
spindle lock pressed during this procedure.
Remove the flange nut (10) from the spindle •
using the spanner (11).
Position the grinding disc on the flange (9).•
Place the flange nut on the spindle and tighten •
it using the spanner.
Release the spindle lock and check that the •
spindle is unlocked by rotating it.
Mounting grinding discs and roughing discs
Fig. 4 and 5 show how to mount the flange (10)
when using thick (4 – 8 mm) and thin (2,5 – 4 mm)
discs.
4. USE
Always observe the safety instructions
and applicable regulations.
Special attention when starting the machine
Clamp the workpiece and make sure that the •
workpiece cannot slide from under the machine
during the cutting activities.
When working with the machine, always hold it •
firmly with both hands and provide for a secure
stance.
Always direct the cable to the rear away from •
the machine.
Insert the mains plug only when the machine is •
switched off.
Apply the machine to the workpiece only when •
switched on
Never use the machine for grinding
magnesium workpieces.
Switching on and off
Slide the on/off switch forwards.•
To switch off, depress the on/off switch, this will •
then jump to the ‘off’ position.
Do not put the machine down when the
motor is still running. Do not place the
machine on a dusty surface. Dust
particles may enter the mechanism.
Operation
Hold the machine firmly and move it against the •
workpiece. Move the grinding disc evenly
across the workpiece.
Move the machine during roughing under an •
angle of 30º - 40º across the workpiece (Fig. 6).
Never use grinding discs for roughing!
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FDAG 750 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FDAG 750 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 11,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info