Manual Ferm ESM1008 - FROS-450 (page 6 of 36) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763830

Zoom out

Zoom in

1/36

Ferm 67

Sørg for at maskinen ikke står under strøm, når der udføres

vedligeholdelsesarbejder på mekanikken.

Maskinerne fra Ferm er udviklet til at fungere længe uden problemer med et minimum af

vedligeholdelse. Ved at rengøre maskinen regelmæssigt og behandle den korrekt, bidrager De

til en længere levetid for maskinen.

Hjælp

Rengøring

Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at

ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til at

fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol, ammoniak,

osv. Den slags stoffer beskadiger kunststofdelene.

Smøring

Maskinen behøver ingen ekstra smøring.

Fejl

Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på

garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan

bestilles.

Miljø

For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er så

vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.

Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres

på en genbrugsplads.

Garanti

Garantibetingelser er beskrevet på det separat vedlagte garantibevis.

• Den elektroniske motor bliver varm: • Rengør ventilationsåbningen

• Støvet bliver ikke opsamlet: • Støvposen er fuld / tøm støvposen

• Slibepapiret er fyldt med klæbestof/ • Maling eller klæbestof er ikke tørt.

maling eller lignene materiale: • Nogle former for maling klæber mere til

slibepapir end andre / rengør ofte

slibepapiret

5. VEDLIGEHOLDELSE

6Ferm

The sandpaper (5) is fixed by Velcro fastener to facilitate the replacement.

• Simply pull off the sanding paper

• Press the new one in the centre of the sanding sole (6)

Coarse sand-paper (grain 50) removes in general the bigger part of the material and fine sand-

paper (grain 120) is used for the finishing.

Replacing the sanding sole

The sole has to be replaced when the Velcro has been worn out.

Before replacing the sanding sole disconnect the sander from the mains.

• Remove the sandpaper of the sole.

• Remove the screws which the sole is fixed to the sander.

• Remove the sole.

• Install the new sole on the sander.

• Tighten the screws well.

Operation

• Push in the on/off switch (1) to start the machine.

• By adjusting the adjusting wheel (8) you can regulate the speed.

• The ventilating apertures (4) on the housing must remain clear to ensure optimum cooling

of the motor.

• Move the sander over the surface of your workpiece.

• Let loose the same on/off switch to stop the machine.

• The on/off switch can be blocked in position “ON” by pushing the lock-on button (9) on the

side, while you keep pushing the on/off switch. The machine can be stopped by briefly

pushing the on/off switch again.

Prevent pushing too much on the machine during sanding. Excessive sanding

pressure does not lead to increased sanding capacity, but increases wear of the

machine and the sandpaper.

Grips

The sander is equipped with two grips: a handle at the front side and one on the back side.

Always hold the sander with both hands on the handles, so as to gain the best possible control

over your sanding operations. Besides you do not risk to become in touch with the moving

parts.

Sanding

The sanding sole of the sander executes small circular movements. Trough this you will get an

even surface without marks.

4. USE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm ESM1008 - FROS-450 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm ESM1008 - FROS-450 Manual

Product: