Manual Ferm EFM1001 (page 6 of 108) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

510109

Zoom out

Zoom in

1/108

6 Ferm



• Place the spring (11) in the mounting hole.

• Position the sanding arm (4).

• Tighten the belt tracking knob (6) until the

sanding arm (4) is alligned with the tool.

Fitting and removing the sanding belt

Fig. C

Fitting the sanding belt

• Move the belt tensioning lever (5) to the A

position.

• Make sure the arrows on the inside of the

sanding belt face the same direction as the

arrow (15) on the housing.

• Slide the sanding belt through the slot in the

housing.

• Place the sanding belt over the rear (14) and

front (13) pulley.

• Move the belt tensioning lever (5) to the B

position.

Adjusting the sanding belt tracking

Fig. D

• Switch the machine on

• Turn the tracking belt (6) as required until the

sanding belt runs straight along the length of

the sanding arm (4)

Removing the sanding belt

Fig. C

• Move the belt tensioning lever (5) to the A

position.

• Slide the sanding belt off the pulleys.



Fig. G

• To switch on the machine in continuous mode,

keep the lock-off button (2) pressed and press

the on/off switch (1).

• To switch off the machine, press the on/off

switch (1) again.



Fig. F

The speed adjustment wheel is used for setting

the speed. The speed adjustment wheel can be

set to 6 positions. The ideal speed depends on the

required grain size and on the material to be

worked.

Do not set the speed during use.

• Turn the speed adjustment wheel (7) to the

required position.

•For hard materials, use a sanding belt with

a fine grain size and select a lower speed.

•For soft materials, use a sanding belt with a

coarse grain size and select a higher

speed.

• After working for longer periods at low speed

you should allow the machine to cool down by

running it at maximum speed with no-load for

approx. 3 minutes.



Fig. E

A complete dust bag is enclosed. Put the wire-

bracket (inside the dust bag) into to the adapter of

the dust bag (when not mounted). The end of the

bracket has to point upwards. Use the dust bag to

collect dust which is released during sanding.

• Put the dust bag on the dust collection

opening

• Empty the dust bag regularly in order to obtain

an efficient dust extraction.

Grip

The use of the belt sander is made easier because

of the two grips one on the front side and one on

the back. Through that you can hold the machine

with two hands, you have a better control of the

machine and there is less risk to becoming in

touch with the moving parts.

Hold the belt sander always with both hands.

Operating instructions

Make sure that the machine has reached its full

speed before placing the machine on the work

piece. This will prevent an overload of the

machine.

The wide arm is for general use, for slotting and for

making joints. (Fig. H)

The narrow arm is finer detail, for cutting and for

carving. (Fig. I)

The angled arm is for grooving and sanding in the

centre of workpieces and in confined areas (A).

Use section B for curved surfaces. (Fig. J)

• Do not bend the sanding belts

• Do not bring too much pressure to your

machine, this will only delay the sanding.

• Regularly check the condition of the sanding

belt. Replace when necessary.

• Always sand with the grain of the wood.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm EFM1001 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm EFM1001 Manual

Product: