Manual Ferm CTM1018 (page 9 of 52) (English, German, Dutch, French, Polish)

763693

Zoom out

Zoom in

1/52

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with a standardised test given in EN

60745; it may be used to compare one tool

with another and as a preliminary assessment of

exposure to vibration when using the tool for the

applications mentioned.

- using the tool for different applications, or with

different or poorly maintainted accessories,

may significantly increase the exposure level.

- the times when the tool is switched off or when

it is running but not actually doing the job, may

significantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns.

Description

The numbers in the following text refer to the

pictures on page 2-3

1. Collet chuck

2. LED work light

3. Spindle lock

4A. Speed adjustment button “+”

4B. Speed adjustment button “-“

5. On/off button

6. Speed indication lights

7. Charger indication light

8. Chuck spanner

3. ASSEMBLY

Always make sure the machine is turned

off before mounting an accessory.

Warning! Change accessories by

inserting an accessory into the collet (or

chuck) as far possible to minimize run out

and unbalance.

Assembly of accessories

Fig. 2

Press down the spindle lock (3) and hold it down.

Using the chuck spanner (8) you can undo the

collet chuck (1). Put the accessory in its place.

Hold down the spindle lock when you fasten the

collet chuck with the chuck spanner.

Do not press the spindle lock button

while the motor is running.

4. OPERATION

Switch on the machine by pressing the on/off

button (5).

With the speed adjustment button “+”(4A)

or “-“(4B) you can regulate the speed of the

Combitool. Do not put the machine down when

the motor is still running. Do not place the

machine on a dusty surface. Dust particles may

enter the mechanism.

Too high a load at a low speed of the

Combitool can burn out the engine.

The battery must be charged before first use.

Charging the device (with the charger)

• Plug the charger plug into an electrical outlet

and wait for a while. The charger indication

light (7) will lighten up and show the charging

status.

LED Charger status

Red Battery charging in progress

Green Battery charging finished, battery fully charged

• After the battery is fully charged remove the

charger plug from the outlet and remove the

small plug from the device.

Holding and guiding the tool

Fig. 3

• For precision work (engraving): pencil grip (A)

• For rough work (grinding): paring knife hand

grip (B)

• When you need to keep the tool parallel to the

work surface (e.g. using a cut-off wheel): 2

hand golf grip (C)

Optimal use of the combi tool and its

accessories

Fig. 1

For optimal use of the accessories use the

correct speed. You can refer to the overview

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CTM1018 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 4,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CTM1018 Manual

Product: