697750
6
Zoom out
Zoom in
Previous page
1/72
Next page
6
EN
Switch off the tool and wait until the blade has
stopped completely before moving the saw
away from the work or putting it down. Hearing
protection should be worn when using circular
saw.
Switch off the machine immediately when you
discover:
A defective mains plug or mains lead;
A defective switch.
Overheating of the circular saw.
Smoke or odeur caused by scorched
insulation.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions. Keep these
instructions in a safe place!
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class II machine – Double insulation –
You don’t need any earthed plug.
Replacing cables or plugs
If the mains cable becomes damaged, it must
be replaced with a special mains cable available
from the manufacturer or the manufacturer’s
customer service. Dispose of old cables or plugs
immediately after replacing them with new ones. It
is dangerous to connect the plug of a loose cable
to a socket.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm2. When using a cable
reel always unwind the reel completely.
3. ASSEMBLY AND ADJUSTING
INSTRUCTIONS
Before adjusting the saw, make sure the
plug is removed from the socket.
Setting the sawing angle (bevel)
Loosen both knobs (12).
Rotate the soleplate to the correct position (0°
- 45°), and tighten the knobs. The sawing angle
(bevel) can be read on the angle indicator (14).
Fitting the parallel guide
Loosen knob (11).
Insert the parallel guide into the slots provided.
Set the correct cut width and tighten the knob
(11).
Setting the cutting depth
Loosen knob (3).
Move the soleplate (7) downwards.
Tighten the clamping knob (3) once the correct
depth is set.
Exchanging or cleaning the saw blade
Use only saw blades recommended by
the manufacturer, which conform to
EN 847-1.
Use the shaft locking knob (13) to prevent the
shaft from rotating.
Next loosen the hexagon screw (6) in the
centre of the saw blade, using the Allen key
provided.
Turn the safety guard to the rear, and hold it
there with the aid of the knob (15).
Withdraw the retaining ring and the saw blade,
and clean the saw blade, or replace it with a
new one.
Again place the saw blade back on the shaft.
Allow the safety guard to return over the saw
blade by releasing the knob (15).
Press the shaft locking knob (13) back in, refit
the retaining ring (8) and tighten the hexagon
screw (6) firmly once more.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CSM1041P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1041P in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info