Manual Ferm CSM1018 - FKS-185L2 (page 4 of 30) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763621

Zoom out

Zoom in

1/30

replacing them with new ones. It is dangerous to connect

the plug of a loose cable to a socket.

Using extension cables

Only use an approved extension cable suitable for the

power input of the machine. The minimum conductor

size is 1.5 mm2. When using a cable reel always unwind

the reel completely.

BEFORE USING THE CIRCULAR SAW:

•Check the following points:

•Does the voltage of the motor correspond with the

mains voltage (appliances for a mains voltage of 230V.

•Are the mains lead and the mains plug in a good

condition: solid, without any loose ends or damage.

•Is the saw blade missing any teeth or showing

any cracks, it so must be replaced immediately.

•Make sure the blade is secure.

•Use this circular saw to saw only wood, wood-like

products.

•Do not use circular saw blades wich are deformed or

damaged.

•Do not use HSS blades.

•Only use blades meeting the required dimensions, as

well as data and descriptions;

Never apply any blades of which the thickness is

greater than that of the riving knife.

•Do not stop the blade of a circular saw by pressing

the blade from the side.

•Check that the blade guard can freely move and fully

closes.

•Never lock-up the guard in the open position.

•Never put sideward pressure on the blade. This may

cause the blade to break.

•Be careful when cutting wood with knots, nails or

cracks in it and/or dirt on it, as these can cause the

blade to get stuck.

•Never leave the circular saw unattended.

•Use this circular saw to saw only wood or wood-like

products.

SAFETY TIPS FOR THE LASER BEAMER.

•Never look into the light beam of the laser.

•Never point the light beam of the laser at humans or

animals.

•Do not point the light beam of the laser at strongly

reflecting material. Hazard from reflected light.

•Only have repairs made to the laser beamer by

qualified personnel / professional repair specialists.

•Do not insert any hard objects into the laser optics.

•Clean the laser optics with a soft, dry brush.

USING THE MACHINE:

•Use clamps or a vice to hold the work.

•Never remove wood chips and saw dust that is close

to the saw blade with your hands. If there are small

pieces of wood left between the fixed and the

movable parts, the circular saw will have to be

stopped. The plug needs to be removed from the

socket, before any left piece can be removed.

•Check that the blade is suitable for the spindle speed

of the circular saw. Do not attempt to cut before the

circular saw has reached full speed. Make sure the

circular saw runs without load (i.e. is not in contact

with the work) when you switch it on. The circular

saw must have reached its full speed first.

•Never cut wood that is thicker than the depth of the

saw blade.

•When cutting in wooden walls or floors, check there

is no wiring or piping where you intend to cut.

•Switch off the tool and wait until the blade has

stopped completely before moving the saw away

from the work or putting it down. Hearing

protection should be worn when using circular saw.

SWITCH OFF THE MACHINE IMMEDIATELY

WHEN YOU DISCOVER:

•A defective mains plug or mains lead.

•A defective switch.

•Overheating of the circular saw.

•Smoke or odeur caused by scorched insulation.

4Ferm Ferm 57

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1018 - FKS-185L2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CSM1018 - FKS-185L2 Manual

Product: