Manual Ferm csm 1030 (page 7 of 68) (English, German, Dutch, Danish, French, Italian)

383746

Zoom out

Zoom in

1/68

Ferm

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Troubleshooting

Below we have listed a few probable causes and

solutions to which you can refer if your circular

saw does not function properly.

1. The temperature of the electric motor ex-

ceeds 70°C.

The motor has been overloaded by working it •

too hard.

Cut more slowly and allow the motor to •

cool down.

The motor is defective.•

Please contact the service address on •

the warranty card.

2. The tool does not work when switched on.

Damaged cord and/or plug.•

Check cord and/or plug.•

Defective switch.•

Please contact the service address on •

the warranty card.

3. When cutting it is very difficult to move the

work forward in a straight line and the cut

is not clean.

The blade is bent or blunt.•

Replace the blade.•

4. The circular saw makes a lot of noise and/

or does not run smoothly.

The carbon brushes are worn.•

Please contact the service address on •

the warranty card.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine.

Regularly clean the machine housing with a

soft cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt.

If the dirt does not come off use a soft cloth

moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc.

These solvents may damage the plastic parts.

Replacing hte carbon brushes

Remove the screws (17).•

Withdraw the carbon brushes (18) from the •

circular handsaw and inspect them for wear.

Place the carbon brushes back in the brush •

holders provided.

Check that the copper contact on the carbon •

brushes makes good contact with the copper

part in the brush holder.

Replace the screws (17) and tighten them •

firmly.

Frequent use will cause the carbon

brushes to wear down. Regular

inspection, after every 30 hours of use,

is essential. If the brushes have worn

down to less than 4 mm, replace.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card. In the back of this manual you find

an exploded view showing the parts that can be

ordered.

Environment

To prevent damage during transport, the

appliance is delivered in a solid packaging which

consists largely of reusable material. Therefore

please make use of options for recycling the

packaging.

Faulty and/or discarded electrical or

electronic apparatus have to be

collected at the appropriate recycling

locations.

Warranty

The warranty conditions can be found on the

separately enclosed warranty card.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm csm 1030 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 8,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm csm 1030 Manual

Product: