383746
6
Zoom out
Zoom in
Previous page
1/68
Next page
GB
6
Ferm
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class II machine Double insulation
You don’t need any earthed plug.
Replacing cables or plugs
If the mains cable becomes damaged, it must
be replaced with a special mains cable available
from the manufacturer or the manufacturer’s
customer service. Dispose of old cables or plugs
immediately after replacing them with new ones.
It is dangerous to connect the plug of a loose
cable to a socket.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
3. ASSEMBLY AND ADJUSTING
INSTRUCTIONS
Before adjusting the saw, make sure the
plug is removed from the socket.
Setting the sawing angle (bevel)
Loosen both knobs (12).•
Rotate the soleplate to the correct position (•
- 45°), and tighten the knobs. The sawing
angle (bevel) can be read on the protractor
(14).
Fitting the ripfence
Loosen knob (11).•
Insert the rip fence into the slots provided.•
Set the correct cut width and tighten the knob •
(11).
Setting the cutting depth
Loosen knob (3).•
Move the soleplate (7) downwards.•
The cut depth of the saw blade can be read •
off on the side of the safety guard.
Tighten the clamping knob (3) once the •
correct depth is set.
Exchanging or cleaning the saw blade
Use the shaft locking knob (13) to prevent the •
shaft from rotating.
Next loosen the hexagon screw (6) in the •
centre of the saw blade, using the Allen key
provided.
Turn the safety guard to the rear, and hold it •
there with the aid of the knob (15).
Withdraw the retaining ring and the saw •
blade, and clean the saw blade, or replace it
with a new one.
Again place the saw blade back on the shaft. •
Allow the safety guard to return over the saw •
blade by releasing the knob (15).
Press the shaft locking knob (13) back in, refit •
the retaining ring (8) and tighten the hexagon
screw (6) firmly once more.
4. OPERATION
Use of hearing protection is
recommended while operating the
circular saw.
Switching On/Off
Press knob (16) with your right-hand thumb •
and keep it depressed.
Press knob (2) to start the saw.•
Release knob (2) to stop the saw.•
Operation
Hold the work using clamps or a vice to have •
both hands free to operate the saw.
Switch on the saw and place the bottom plate •
on the work.
Slowly move the saw towards the previously •
drawn cutting line and slowly press the tool
forward.
Firmly press the bottom plate on the work, •
otherwise the circular saw may start to
vibrate, causing the blade to break more
easily.
Let the saw do the job. Do not put undue
pressure on the circular saw.
5. MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
The machines have been designed to operate
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm csm 1030 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm csm 1030 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 8,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info