Manual Ferm CRM1042 (page 7 of 36) (English, German, Dutch, French, Spanish)

632693

Zoom out

Zoom in

1/36

Ferm

compressor will not move when in operation. If the

surface area is a board or a shelf of a bookcase,

just make sure that they cannot fall down by

securing them properly. For proper ventilation and

effective cooling, it is important that the

compressor is positioned at least 100 cm from the

wall (fig. 4).

Make sure that the compressor is

transported in the right way, do not turn it

upside down and don’t lift it with hooks or

ropes (fig. 5-6).

Installing the air filter.

Remove the transport lids and replace them with

the supplied air filter before using the compressor

Starting up

• Check whether the mains voltage corresponds

to that indicated on the electrical specification

plate (fig. 10), the permitted tolerance range

should be within 5%.

• Press the switch (3) situated on the upper part

into the “0” position according to the pressure

regulator type fitted on the device (fig. 11).

• Put the plug in the plug socket (fig. 9) and start

the compressor up by putting the switch of the

pressure regulator in the “I” position. The

operation of the compressor is fully automatic.

The pressure regulator will stop the

compressor when the maximum value has

been reached and start it up when the

pressure drops below the minimum value.

Normally the difference in pressure is approx.

2 Bar/29 psi between the maximum and the

minimum value. For instance - The

compressor will stop when it reaches 8 Bar

(116 psi) (this is the maximum operating

pressure) and will start up automatically when

the pressure within the tank has dropped to 6

Bar (87 psi).

The head/cylinder/transmission pipe

assembly may reach high temperatures,

so take care when working close to these

parts and do not touch them to avoid

burns (fig. 12 - 13).

Adjusting the operating pressure

Fig. 14

It is not necessary continuously to use the

maximum operating pressure, the compressed-air

tools often require less pressure. With regard to

compressors supplied with a pressure reduction

valve it is necessary to set the operating pressure

properly.

It is possible to set the operating pressure by using

the turning knob on the reduction valve.

• By turning clockwise, the pressure will be

increased.

• By turning anti-clockwise, the pressure will be

reduced.

The compressor has two pressure gauges and

two points to connect an air hose:

• Pressure gauge on the left (9): pressure on left

outlet (7). The pressure of left this outlet can

be regulated with help of the reduction valve

(5).

• Pressure gauge on the right (8): tank pressure

+ pressure on right outlet (6)

Hints for accurate adjustment of the pressure

regulation:

• Turn the turning knob (5) anti-clockwise till

pressure is fully released

• -Connect the air tool you want to use to the

left quick coupler (6)

• Activate the air too shortly, so the pressure

gauge (7) will show the right pressure level

• Turn the turning knob (5) clockwise, till the

pressure gauge (7) shows the pressure level

you need

• Your air tool is now ready to use.

Note: when not connecting an air tool while

adjusting the pressure, it might occure the

pressure gauge (7) is not reacting accurately on

the pressure drop

4. Maintenance

Make sure that the power plug is removed

from the mains when carrying out

maintenance work on the motor.

The machine has been designed to operate over a

long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning. Before interfering in any way whatsoever

with the compressor, please make sure that:

• The switch button (3) is in the “0” position and

the power plug is removed from the power

socket

• The air tank is fully decompressed (both

pressure gauges must be pointed at 0 Bar)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CRM1042 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 4,39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CRM1042 Manual

Product: