Manual Ferm CRM1033 FCO-1006N (page 7 of 26) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

538653

Zoom out

Zoom in

1/26

46 Ferm

Sørg for at jordforbindelsen er tilsluttet, før

stikket på tilførslen udskiftes. Hvis du skulle

ære i tvivl, bør du ringe til en elektriker og få

jordforbindelsen checket efter.

Forlængerledninger

Lange elkabler, forlængerkabler, kabeltromler og

lignende kan forårsage spændingsfald og kan

forhindre motoren i at starte. Træghed kan gøre

det vanskeligt at starte ved lave temperaturer

under frysepunktet (0°C). Anvend kun forlæng-

erledninger med stik og jordforbindelse, anvend

derfor aldrig beskadigede eller trykkede forlæng-

erledninger. Check om forlængerledningen er i

god stand. Ved anvendelse sammen med dette

apparat, skal ledningen have et tværsnit på

mindst 2.5 mm

(dette passer med en maksimal

længde på 20 meter). Rul altid

forlængerledninger helt ud før du anvender dem.

Elektriskforbindelse

Sørg altid for om den indgående spænding til

motoren stemmer overens med

hovedspændingen vist på typepladen.

Kompressoren er udstyret med et elektrisk kabel

og et to-polsstik + jordforbindelse. Det er vigtigt

at tilslutte kompressoren til en jordbunden

stikkontakt. (Fig. 9)

Anvend aldrig jordforbindelsen istedet

for den neutrale (0-ledning).

Jordforbindelse bør kun anvendes i

overenstemmelse med regler for

uheldsforbyggelse.

3. ANVENDELSE

Kun til anvendelse i hjemmet

Bemærk: Informationen i denne vejledning er

skrevet for at assisterer brugeren i betjening og

vedligeholdelse af kompressoren. Nogle

illustrationer i denne vejledning viser detaljer som

kan afvige fra dem på deres kompressor.

Installation

Når kompressoren er taget ud af emballagen (fig.

1), skal det kontrolleres, at den er i perfekt

stand og ikke udviser transportskader. Derefter

foretages følgende: Hvis de ikke allerede er

sat på, monteres gummifødderne og hjulene på

tanken som vist i fig. 2. Anbring kompressoren

på en flade, som er vandret eller maksimalt har

n skråning på 10° (fig. 3), i et område med

god ventilation, hvor den er beskyttet mod

påvirkninger fra atmosfæren, og ikke i

eksplosionsfarlige omgivelser.

Hvis underlaget skråner og er glat, skal det

sikres, at kompressoren ikke flytter sig under

brugen. Hvis underlaget er et bræt eller en

reolhylde, skal det fastgøres forsvarligt, så det

ikke falder ned. For at sikre passende ventilation

og effektiv køling er det vigtigt, at kompressoren

placeres mindst 100 cm fra væggen (fig. 4).

Sørg for at kompressoren er korrekt trans-

porteret, vend den ikke på hovedet og løft

den ikke med kroge og reb (fig. 5-6).

Start

• Check om hovedspændingen stemmer

overens med den som er indikeret på den

elektriske typeplade (fig. 10), den tilladte

tolerance rækkevidde bør være inden for 5%.

• Tryk på knappen placeret på øverste del ind til

“0” position, efter typen på trykregulatoren

monteret på enheden (fig. 11).

• Put stikket i stikkontakten (fig. 9), og start kom-

pressoren ved at sætte knappen på trykregu-

latoren i “I” position. Driften af kompressoren

er totalt automatisk. Trykregulatoren vil stoppe

kompressoren når den maksimale værdi er

opnået, og starte op når trykket falder til under

minimumværdien.

Normalt er forskellen i tryk ca. 2 Bar/29 psi

mellem maksimum og minimum værdi. F.eks. -

Kompressoren vil stoppe når den opnår 8 Bar

(116 psi) (dette er det maksimale tryk ved

drift), og vil automatisk starte op når trykket i

tanken er faldet til 6 Bar (87 psi).

Hovedet/cylinder/transmissionsrør

kan opnå høje temperaturer, så hver

forsigtig når der arbejdes tæt på

disse dele, og for at forebygge

forbrændinger (fig. 12-13) bør du

ikke komme i kontakt med dem.

Ferm 07

compressor on a flat surface or at a maximum

slope of 10° (fig.3), in a well ventilated area,

protected against atmospheric factors and not in

explosive surroundings. If the surface area is

sloping and smooth, make sure that the

compressor will not move when in operation. If

the surface area is a board or a shelf of a

bookcase, just make sure that they cannot fall

down by securing them properly. For proper

ventilation and effective cooling, it is important

that the compressor is positioned at least 100 cm

from the wall (fig. 4).

Make sure that the compressor is

transported in the right way, do not turn

it upside down and don't lift it with

hooks or ropes (fig. 5-6).

Starting up

• Check whether the mains voltage corresponds

to that indicated on the electrical specification

plate (fig. 10), the permitted tolerance range

should be within 5%.

• Press the switch situated on the upper part

into the "0" position according to the pressure

regulator type fitted on the device (fig. 11).

• Put the plug in the plug socket (fig. 9) and start

the compressor up by putting the switch of the

pressure regulator in the "I" position. The

operation of the compressor is fully automatic.

The pressure regulator will stop the

compressor when the maximum value has

been reached and start it up when the

pressure drops below the minimum value.

Normally the difference in pressure is approx.

2 Bar/29 psi between the maximum and the

minimum value. For instance - The compressor

will stop when it reaches 8 Bar (116 psi) (this is

the maximum operating pressure) and will start

up automatically when the pressure within the

tank has dropped to 6 Bar (87 psi).

The head/cylinder/transmission pipe

assembly may reach high temperatures,

so take care when working close to

these parts and do not touch them to

avoid burns (fig. 12 - 13).

Adjusting the operating pressure

Fig. 14

It is not necessary continuously to use the maxi

mum operating pressure, the compressed-air

tools often require less pressure. With regard to

compressors supplied with a pressure reduction

valve it is necessary to set the operating pressure

properly.

It is possible to set the operating pressure by

using the turning knob on the reduction valve.

• By turning clockwise, the pressure will be

increased.

• By turning anti-clockwise, the pressure will be

reduced.

The set pressure can be locked by turning the

ring under the turning knob in the opposite

direction from the turning knob thereby fixing the

turning knob. The set pressure is visible on the

manometer of the reduction valve.

4. MAINTENANCE

Make sure that the plug is removed

from the mains when carrying out

maintenance work on the motor.

The machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning. Before interfering in any way

whatsoever with the compressor, please make

sure that:

• The general line switch is in the "0" position.

• The pressure regulator and the switches on

the switch board are switched off in the "0"

position.

• The air tank is fully decompressed.

Malfunction

Should the machine fail to function correctly, a

number of possible causes and the appropriate

solutions are given below:

Air loss

• May be caused by a poor seal of a

connection.

• Check all connections by wetting them with

soap and water.

The compressor runs but does not compress

Fig. 19

• May be caused by the valves (C-C2) or a

gasket (B1-B2) being broken.

•

Replace the damaged part.

The compressor will not start

• If the compressor is difficult to start, check:

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CRM1033 FCO-1006N in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CRM1033 FCO-1006N Manual

Product: