Manual Ferm CRM1033 FCO-1006N (page 6 of 26) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

538653

Zoom out

Zoom in

1/26

Ferm 47

Juster driftstrykket

Fig. 14

Det er ikke nødvendigt at anvende det maksimale

driftstryk konstant, trykluftsværktøjet kræver ofte

mindre tryk. Ved kompressorer leveret med en

trykreducerende ventil, er det nødvendigt at

indstille driftstrykket korrekt. Det er muligt at

indstille driftstrykket ved at anvende

drejeknappen på reductionsventilen.

• Ved at dreje denne med uret, vil trykket øges.

• Ved at dreje denne mod uret, vil trykket

mindskes.

Det indstillede tryk kan låses ved at dreje ringen

under drejeknappen i den modsatte retning af

drejeknappen, herved fastlåses drejeknappen.

Det indstillede tryk er synligt på trykmåleren på

reduktionsventilen.

4. VEDLIGEHOLDELSE

Sørg for, at stikket til maskinen er

taget ud af stikkontakten, når der

skal udføres vedligeholdelse på

motoren.

Maskiner er blevet konstrueret, så de kan arbejde

i længere perioder med et minimum af

vedligeholdelse. Korrekt vedligeholdelse og

rengøring af maskinen er en forudsætning for

lang tids tilfredsstillende brug. Før enhver form

for vedligeholdelse foretages, sørg altid for at:

• Universalknappen er står "0" positionen.

• Tryk regulatoren og kontakterne på strøm-

fordelingstavlen er slukket i "0" positionen.

• Lufttanken er helt uden tryk.

Lufttab

• Kan være forårsaget af en dårlig tætning af en

forbindelse.

• Check alle forbindelser ved at væde dem

med sæbe og vand.

Kompressoren køre men komprimere ikke

Fig. 19

• Kan være forårsaget af ventilerne (C-C2) eller

en pakning (B1-B2) som er ødelagt.

• Udskift de ødelagte dele.

Kompressoren vil ikke starte

Hvis kompressoren er svær at starte, check:

•

Om hovedspændingen stemmer overens med

den på typepladen (fig. 10)

• Om elektriske forlængerledninger anvendes

med en kernefejl eller længdefejl.

• Om arbejdsmiljøet for for koldt (under 0°C).

• Om der strømforsyning (stik korrekt forbundet,

magneto termiske sikringer ikke er ødelagte).

Kompressoren vil ikke slukke

Hvis kompressoren ikke slukkes når det

maksimale tryk er opnået, vil sikkerhedventilern

på tanken aktiveres.

Det er nødvenligt at kontakte den nærmeste

autoriserede support servicevirksomhed for

reparation.

Rengøring

Kappen omkring motoren skal rengøres med en

blød klud, helst hver gang maskinen har været

brugt. Ventilationsrillerne skal holdes fri for støv

og snavs. Hvis snavset ikke vil gå af, bruges en

blød klud vredet op i sæbevand. Der må ikke

bruges opløsningsmidler som f.eks. benzin, sprit,

salmiakspiritus o.l. Sådanne opløsningsmidler

kan beskadige dele af plastic.

Smøring

Det er anbefalet at skille sugefiltret ad hver

50ende driftstime, og rengøre filterelementet ved

at puste det ved lufttryk (fig. 15). Det er anbefalet

ar filterelement udskiftes mindst to gange hvert år

hvis kompressoren arbejder i et rent miljø; ofterer

hvis arbejdsmiljøet er støvet. Kompressoren

udvikler kondensvand som samles i tanken.

Det er nødvendigt at fjerne kondensvand i tanken

mindst én gang om ugen, ved at åbne aftapnings-

hanen (fig. 16) under tanken. Vær forsigtig når

trykluft er i flasken, da vand kan komme ud under

stort tryk. Anbefalet tryk maks. 1-2 Bar.

Fejl

Skulle en fejl opstå, f.eks. pga. slidtage af en

enhed, kontakt venligst serviceadressen på

garantibeviset. På bagsiden af denne manual

finder du en tegning med alle dele, der kan

bestilles.

Miljø

For at undgå transportbeskadigelse leveres

maskinen i en solid emballage. Emballagen er så

vidt muligt lavet af genbrugsmateriale. Genbrug

derfor emballagen.

Ferm

reach high temperatures. Do not touch these

parts to avoid burns (fig. 12-13).

•

Transport the compressor by lifting it or by

using the special grips or handles (fig. 5-6).

• Children and animals should be kept far away

from the area of operation of the machine.

• If you use the compressor to spray paint:

a) Do not work in enclosed spaces or near

naked flames.

b) Make sure that the environment in which

you will be working has dedicated

ventilation.

c) Protect your nose and mouth with a

dedicated mask (fig. 21).

• Do not use the compressor when the electrical

cable or the plug is damaged, and instruct an

authorised Support Service to replace them

with an original part.

• When the compressor is placed on a surface

higher than the floor, it should be secured to

prevent it from falling down during operation.

• Do not put objects or your hands in the

protective covers to avoid physical damage

and damage to the compressor.

• Do not use the compressor as a blunt

instrument against persons, objects or animals

in order to prevent serious damage.

• If the compressor is no longer in use, always

take the plug out of the plug socket.

• Always make sure that compressed-air hoses

are used for compressed air and which are

characterised by a maximum pressure

adjusted to that of the compressor. Do not try

to repair the hose if it is damaged.

Electrical safety

Earthing regulations

This compressor has to be earthed while in use

in order to protect the operator against electrical

shocks. The compressor is provided with a two-

core cable plus an earth. The electrical

connection has to be made by a qualified

technician. We recommend never disassembling

the compressor and neither making any other

connections into the pressure regulator. Repairs

should be carried out by authorised Support

Services or by other qualified centres.

Never forget that the earthing core is

the green or the yellow/green wire.

Never connect this green wire to a

terminal under load.

Before replacing the plug of the feed, make sure

that the earth cable is connected. If in doubt,

lease call in a qualified electrician and have the

earthing checked.

Extension cables

Long supply lines, extensions, cable reels and

similar cause voltage dips and may prevent the

motor from starting. Sluggishness makes starting

difficult at low temperatures under freezing point

(0°C). Only use an extension cable with a plug

and earth, so never use damaged or flattened

extension cables.

Check whether the extension cable is in a good

condition. For this device the extension cable

should have a diameter of at least 2.5 mm

(this

applies to a maximum length of 20 metres).

Always unroll extension cables fully before using

them.

Electrical connection

Always check whether the input voltage of the

motor corresponds to the mains voltage indicated

on the specification plate. The compressors are

supplied with an electrical cable and a two-pole

plug + earth. It is important to connect the

compressor with an earthed plug socket. (fig. 9)

Never use the earth-wire instead of the

neutral (0-wire). The earthing should

take place in accordance with accident

prevention regulations.

3. USE

For homehold use only

NB: The information you will find in this manual

has been written to assist the operator in the use

and maintenance of the compressor. Some

illustrations in this manual show details which

may differ from those of your compressor.

Installation

After having taken the compressor out of its

packaging (fig. 1) and having checked that it is in

perfect condition, and having noted that no

damage occurred during transport, the following

acts should be performed. If not yet fitted, fit the

rubber feet and the wheels on the tank according

to the instructions represented in fig. 2. Place the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CRM1033 FCO-1006N in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CRM1033 FCO-1006N Manual

Product: