Manual Ferm CDM1146 (page 10 of 72) (English, German, Dutch, French, Italian, Polish, Spanish, All languages)

762290

Zoom out

Zoom in

1/72

ensures that the tool spindle is locked and the

blade screw can be loosened.

• Set the direction switch (5) to the middle

position.

• Remove the blade guard (15) by loosing the

blade guard screw(18) (fig. E), lift up the left

side and slide to the right.

• Unscrew the blade screw (16) (fig. F).

• Remove the blade (17)

• Place the new blade, ensure that the sloping

edge of the blade faces you (fig. G)

• Retighten the blade screw (16)

• Place the blade guard (15) back and retighten

the blade guard screw (18).

Working Advice

Do not overload the machine, when

overloading the machine it may come to

a standstill.

• The cutting performance depends on the

materials to be cut. When machine is fully

charged the result will be better.

• Always make sure the blade is clean and free

form excess materials.

• Make sure nothing can get wedged during

cutting by holding the guide edge (14) parallel

to the cutting surface.

• Especially thin materials, such as fabrics, can

be pulled into the machine during cutting.

Always be careful and do not apply too much

pressure in order to achieve good cutting

results. Apply sufficient tension to the fabrics

and cut slowly.

• Improper use of the blade will cause it to

become blunt.

• Optimum cutting results are best determined

through testing on a small part of the material.

4. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and/or remove the

battery pack from the machine.

• Remove the cutting adapter from the

screwdriver to clean it. There is danger of

injury when unintentionally actuating the On/

Off switch.

• Be careful when cleaning the blade and

counterblade. The blades have sharp edges

which you can injure yourself on.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and

dirt. Remove very persistent dirt using a soft

cloth moistened with soapsuds. Do not use any

solvents such as gasoline, alcohol, ammonia,

etc. Chemicals such as these will damage the

synthetic components.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be collected

at the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic

waste. According to the European Guideline

2012/19/EC for Waste Electrical and Electronic

Equipment and its implementation into national

right, power tools that are no longer usable must

be collected separately and disposed of in an

environmentally friendly way.

WARRANTY

FERM products are developed to the highest

quality standards and are guaranteed free of

defects in both materials and workmanship for the

period lawfully stipulated starting from the date

of original purchase. Should the product develop

any failure during this period due to defective

material and/or workmanship then contact your

FERM dealer directly.

The following circumstances are excluded from

this guarantee:

• Repairs and or alterations have been made

or attempted to the machine by unauthorized

service centers.

• Normal wear and tear.

• The tool has been abused, misused or

improperly maintained.

• Non-original spare parts have been used

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1146 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish, All languages as an attachment in your email.

The manual is 7,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CDM1146 Manual

Product: