762290

Ferm CDM1146 Manual

9
Zoom out
Zoom in
Previous page
1/72
Next page
9
EN
3. OPERATING
The machine must be charged before
first use.
Charging the machine
Fig. D
• Plug the charger cable (included) into an
adapter (not included).
• Plug the charger cable (2) into the machine.
• Plug the charger plug into an electrical outlet
and wait for a while. The charger indication
light (3) will lighten up and show the charging
status.
Fully charging the battery may take up to 2 - 3
hours.
Checking the battery charge status
Fig. D
The battery indication light (3) shows the remaining
battery charge when the on/off switch (6) is pressed.
The battery indication light (3) has three lights
indicating the remaining charge level. The more
lights that burn, the more charge the battery has left.
When the RED light is burning, it means the
battery is almost empty and should be charged.
Fitting and removing drills or screwdriver bits
Fig. C
The machine bit holder (4) is suitable for drills and
screwdriver bits with a standard ¼ inch hexagonal
shaft. To fit a screwdriver bit:
• Insert the screw driver bit (10) into the
machine’s bit holder (4), it will be hold by a
magnet.
• The screw driver bit can be removed by pulling
it out of the bit holder again.
The same steps can be followed after a driver
head attachment is mounted (read: Cutting head/
Angle Driver Head Attachements)
Adjusting the direction of rotation
Fig. A
• Set the direction switch (5) to position ‘’ in
order to drive screws or to use it for drilling.
• Set the direction switch (5) to position ‘’ in
order to remove screws.
Switching the machine on and off
Fig. A
• Pressing the on/off switch (6) will activate the
machine.
• Releasing the on/off switch (6) will stop the
machine.
• Move the direction switch (5) to the middle
position to lock the movement of the on/off
switch. It cannot be activated in this position.
The machine is equipped with electronic
overload protection function. When the
machine gets overloaded it will shut
down automatically. When this happens,
please wait for at least 5 seconds to let
the overload protection reset itself.
Spindle lock function
The machine is fitted with an automatic spindle
lock feature. When the on/off switch (6) is not
pressed, the bit holder (4) rotation is locked. Now
it is possible to use the screwdriver (even when
the battery is empty) as a manual tool.
Cutting head/Angle Driver Head
Fig. B
The cutting head (12) can be used to cut trough
textile, cardboard and paper.
The angle driver head (13) allows screwdriving at
hard to reach locations. The attachments can be
mounted offset in different angles.
To assemble an attachment:
• Move the direction switch (5) to the middle
position, preventing accidental activation of
the on/off switch.
• Pull off the cover (9) towards the front.
• Carefully push the attachment onto the
machine.
To disassemble an attachment:
• Move the direction switch (5) to the middle
position.
• Push the unlock buttons (11) on both sides of
the machine.
• Carefully pull the attachment off the machine.
Changing the Blade
Fig. E - G
Note: Replace the blade only when the cutting
adapter is mounted on the screwdriver. This
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1146 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1146 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish, All languages as an attachment in your email.

The manual is 7,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info