763855
7
Zoom out
Zoom in
Previous page
1/124
Next page
7
EN
Plug the charger plug into an electrical outlet
and wait for a while. The LED indicators on
the charger (6) will lighten up and show the
charger status.
LED indicators (6)
Fig.C
The charger has 2 LED indicators (6) which
indicate the status of the charging process:
Red LED
status:
Green LED
status: Charger status
Off Off No power
On Off
Standby mode:
-No battery is inserted or,
-Battery inserted but charging has
finished more then 2 hours ago
Blinking Blinking Defective battery
On Blinking Battery charging in progress
On On Battery charging finished, battery
fully charged
Blinking Off
Battery is too hot, charging
progress is on hold. Charging will
start automatically after the battery
has cooled down.
Fully charging the battery may take up to 60
minutes.
After the battery is fully charged remove the
charger plug from the outlet and remove the
battery from the charger.
The battery can be stored or directly installed
on the machine.
Lithium-Ion cells can be stored for a long
period without losing much of their
charge. When the machine is not being
used over a longer period of time it is best
to store the battery in charged condition.
Fitting and removing drills or screwdriver bits
Fig. A
Always remove the battery before
mounting an accessory.
The drill chuck (7) is suitable for drills and
screwdriver bits with round shaft as well as
hexagonal shaft.
Hold the machine firmly with one hand
Open the drill chuck (7) by rotating the chuck
sleeve with your other hand in clockwise direction
until it is opened far enough for the bit to slide in.
Insert the shaft of the drill or screwdriver bit
Tighten the drill chuck again by firmly rotating
the chuck sleeve counterclockwise.
Check if the bit is centered well by shortly
activating the machine´s on/off switch.
Adjusting the gears
Fig. A
Never switch gears when the motor is
running, this will damage your machine.
Never put switch in the middle between
both positions, this will damage your
machine.
The machine has 2 drill speeds, which can be
adjusted by sliding the gear switch (9) forward or
backwards. The number on the gear switch (9)
shows which position is chosen.
Position 1: For slow drilling, large drilling
diameter or screw driving. The machine has
high power at a low speed.
Position 2: For fast drilling or small drilling
diameter.
Adjusting the direction of rotation
Fig. A
Set the direction switch (10) to position “” in
order to drive screws or to use it for drilling.
Set the direction switch (10) to position “” in
order to remove screws
Switching the machine on and off
Fig. A
The on/off switch (11) is used for activating the
machine and adjusting rotation speed.
Pressing the on/off switch (11) will activate
the machine, the further the switch is being
pushed, the faster the drill will turn.
Releasing the on/off switch (11) will stop the
machine.
Move the direction reversing switch (10) to the
middle position to lock the movement of the on/
off switch. It cannot be activated in this position.
Only lay down the machine when it has
stopped running completely. Do not
place it on a dusty surface as particles of
dust could get into the mechanism.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1141P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1141P in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 16,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info