763851
8
Zoom out
Zoom in
Previous page
1/20
Next page
8
EN
LED indicator (6)
Fig. C
Thechargerhas2LEDindicators(6)which
indicate the status of the charging process:
LED Charger status
Red Battery charging in progress
Green Battery charging finished, battery fully charged
• Fullychargingthe1.5Ahbatterymaytakeup
to 60 minutes.
• Afterthebatteryisfullychargedremovethe
charger plug from the outlet and remove the
battery from the charger.
When the machine is not being used over
a longer period of time it is best to store
the battery in charged condition.
Fitting and removing drills or screwdriver bits
Fig. D
Always remove the battery before
mounting an accessory.
Thedrillchuck(7)issuitablefordrillsandscrewdriver
bits with round shaft as well as hexagonal shaft.
• Holdthemachinefirmlywithonehand
• Openthedrillchuck(7)byrotatingthechuck
with your other hand in clockwise direction until
it is opened far enough for the bit to slide in.
• Inserttheshaftofthedrillorscrewdriverbit
• Tightenthedrillchuckagainbyfirmlyrotating
thechuck(7)counterclockwise.
• Checkifthebitiscenteredwellbyshortly
activating the machine´s on/off switch.
Adjusting the gears
Fig. D
Never switch gears when the motor is
running, this will damage your machine.
Never put switch in the middle between both
positions, this will damage your machine.
The machine has 2 drill speeds, which can be
adjustedbyslidingthegearswitch(8)forwardor
backwards.Thenumberonthegearswitch(8)
shows which position is chosen.
• Position1:Forslowdrilling,largedrilling
diameter or screw driving. The machine has
high power at a low speed.
• Position2:Forfastdrillingorsmalldrilling
diameter
Adjusting the direction of rotation
Fig. E
• Setthedirectionswitch(9)toposition in
order to drive screws or to use it for drilling.
• Setthedirectionswitch(9)toposition in
order to remove screws.
Switching the machine on and off
Fig. E
Theon/offswitch(10)isusedforactivatingthe
machine and adjusting rotation speed.
• Pressingtheon/offswitch(10)willactivate
the machine, the further the switch is being
pushed, the faster the drill will turn.
• Releasingtheon/offswitch(10)willstopthe
machine.
• Movethedirectionreversingswitch(9)tothe
middle position to lock the movement of the
on/off switch.
Adjusting the torque
Fig. E
The machine has 17 different torque settings
and a special drill mode to set the power being
transmitted to the chuck.
Byrotatingthetorqueadjustmentring(11),
screws can be driven to a predetermined depth,
which is ideal for repetitive work. The higher the
number, the more torque will be transmitted.
• Selectalowsettingforsmallscrewsorsoft
work material.
• Selectahighsettingforlargescrews,hard
work materials and when removing screws.
• Youshouldpreferablychooseasettingas
lowaspossiblewhendrivingscrews.Select
a higher setting if the motor slips before the
screw is fully tightened.
• Fordrilling,turnthetorqueadjustmentring(11)
tothesettingfordrilling( ) by fully turning it
counterclockwise.
Ensure that the direction switch (9) is
always set to during drilling.
The machine is equipped with electronic
overload protection function. When the
machine gets overloaded it will shut
down automatically. When this happens,
please wait for a few seconds to let the
overload protection reset itself.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1133 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1133 in the language / languages: English, Dutch as an attachment in your email.

The manual is 3,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info