Manual Ferm CDM1086 (page 8 of 60) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

510091

Zoom out

Zoom in

1/60

Ferm

position ‘±’ in order to remove screws.

Drilling

• Rotate the torque adjustment ring (5) to the

drilling position.

Ensure that the direction reversing

switch (1) is always set to ‘’ during

drilling.

Switching the device on and off

Fig. A

• Depress the on/off switch (4). It regulates the

speed of the appliance by transmitting power

to the switch.

• Release the on/off switch (4) to halt the drill

chuck immediately, it will no longer run on.

• Move the direction reversing switch (1) to the

centre in order to lock the appliance in its

disabled state.

Only lay down the appliance when it has stopped

running completely. Do not place it on a dusty

surface as particles of dust could get into the

mechanism.

Spirit level

Fig. H

The drill is equipped with a dual reading horizontal/

vertical level to assist in keeping the drill “level”

while drilling horizontal and vertical holes. The

horizontal level (13) is located in the top of the drill

housing. The vertical level (14) is located on the

rear of the drill housing.

To maintain a level drilling position, hold the drill

where the level bubble is centred in the level

indicator circle.

Charging the battery

• The included battery is delivered in partly

charged condition.

• Only use the battery charger in a temperature

range between + 5 °C to + 40 ºC.

• Only use the battery charger in dry, ventilated

rooms.

Charging

Fig. F

One advantage of using Lithium-Ion batteries is

that, until the battery is almost empty, hardly any

power fading is noticeable. The machine can be

used until you start noticing that the power of the

drill is elapsed. The battery is discharged now and

needs to be charged.

Charging the battery

Fig. F

• Place the battery stem (9) into the matching

cavity on top of the charger (10).

• Make sure the battery stem is pressed fully

into the charger as far as it will go.

• Plug the charger into the electrical outlet.

LED indicators

Fig. G

When the battery charger is plugged in and the

battery inserted, the battery charger will begin

charging the battery. The red LED (11) and the

green LED (12) on top of the charger will indicate

the charging status.

• When the charger is plugged in without a

battery inserted, the green LED (12) will be lit

up.

• When a battery is inserted, the red LED (11)

will start blinking, indicating charging has

started.

• When the battery is full, charging will stop and

the green LED (12) will start blinking.

• If the battery is left in the charger, the charger

will go on standby after 2 hours. The green

LED (12) will stop blinking and light up.

When an error occurs the red LED (11)

will be lit up.

If the temperature of the battery is too

high to get charged safely, both the

green LED (12) and red LED (11) will be

lit, indicating charging process is on

hold. Charging will start when the

battery has cooled down.

Lithium-Ion cells can be stored for a

long period without losing much of their

charge. When the machine is not being

used over a longer period of time, it is

best to store the battery in charged

condition.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1086 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CDM1086 Manual

Product: