510091

Ferm CDM1086 Manual

7
Zoom out
Zoom in
Previous page
1/60
Next page
GB
7
Ferm
Electrical safety
Always check that the voltage on the
battery block corresponds to the voltage
on the rating plate. Also check that your
mains voltage corresponds to the input
voltage of the battery charger.
Class II machine – Double insulation –
You don’t need any earthed plug.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones.
• Remove the battery block when the power tool
is not being used and prior to maintenance.
• The tool is suitable for use as a screwdriver
and drill. Any other application is specifically
excluded.
3. MOUNTING ACCESSORIES
Prior to mounting an accessory always
remove the battery.
Fitting and removing drill cutters
Fig. B
In addition to screwdriver bits with a hexagonal
shaft, this tool can also accommodate drill bits with
a hexagonal shaft.
• Loosen the drill chuck (6) by rotating the hand-
grip (8).
• Insert the shaft of the drill cutter into the chuck.
• Tighten the drill chuck so that the drill cutter is
firmly clamped.
• Rotate the drill chuck in the opposite direction
when you wish to change the cutter.
Connecting and removing the battery
Fig. C
Ensure that the exterior of the battery
block or tool is clean and dry before
connecting the charger.
• Ensure that the direction reversing switch (1,
Fig. A) is in the central position in order to
prevent the appliance from being switched on
unexpectedly.
• Insert the battery (3) into the base of the
appliance, as shown on the illustration. Push
the battery until it latches in.
• Press the locking buttons (2) on both sides
before removing the battery, and disengage
the battery from the base of the appliance.
4. OPERATION
Always follow the safety notes and the
relevant safety code.
Hold the appliance firmly and press the drill
steadily onto the workpiece. Do not overload the
appliance. Only use drills with no visible wear.
Worn drills will have a bad effect on the functioning
of the appliance.
Adjusting the speed
Fig. D
The appliance has two drill speeds.
• For slow drilling or for driving or removing
screws, set the speed selection switch (7) to ‘1’.
• For fast drilling set the speed selection switch
(7) to ‘2’.
Never switch over when the motor is
running!
Adjusting the torque
Fig. E
The appliance has 21 different torque settings with
which to set the power for driving and removing
screws.
• Set the torque adjustment ring (5) to the
desired position. The available torque settings
are indicated on the adjustment ring by the
numbers 1 to 21 and by dots between the
figures to define intermediate settings.
• You should preferably choose a setting as low
as possible when using the screwdriver.
Select a higher setting if the motor slips.
Driving and removing screws
Fig. A
• Set the direction reversing switch (1) to
position ‘’ in order to drive screws.
• Set the direction reversing switch (1) to
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1086 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1086 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info