763848
6
Zoom out
Zoom in
Previous page
1/92
Next page
6
EN
coarse sanding belt.
- Use a ne sanding belt (grain 120) for
nishing surfaces.
Make sure that the sanding belt (12) is straight
and centred around the sanding pad (3) and
the sanding belt rollers (4).
Tighten the clamping lever (5).
Removing
Place the machine on its side with the V-belt
cover (11) facing downwards.
Release the clamping lever (5).
Remove the sanding belt (12).
Tighten the clamping lever (5).

If the sanding belt does not run parallel with the
outer edge of the housing, the sanding belt must
be centred.
Turn the centring knob (6) clockwise to move
the sanding belt (12) to the inside.
Turn the centring knob (6) counterclockwise to
move the sanding belt (12) to the outside.
USE

To switch on the machine, press the on/off
switch (1).
To switch the machine to continuous mode,
keep the on/off switch (1) pressed and
simultaneously press the lock-on button (2).
To switch off continuous mode, press the
on/off switch (1) again.
To switch off the machine, release the on/off
switch (1).

Insert the dustbag (13) into the dustbag
connection (9).
Hints for optimum use
Clamp the workpiece.
Hold the machine with one hand on the main
grip and the other hand on the auxiliary grip.
Switch on the machine.
Place the sanding belt on the workpiece.
Slowly move the machine over the workpiece,
rmly pressing the sanding belt against the
workpiece.
Do not apply too much pressure on the machine.
Let the machine do the work.
Switch off the machine and wait for the machine
to come to a complete standstill before putting
the machine down.
CLEANING AND MAINTENANCE
3 Before cleaning and maintenance,
always switch off the machine and
remove the mains plug from the mains.
Regularly clean the housing with a soft cloth.
Keep the ventilation slots free from dust and
dirt. If necessary, use a soft, moist cloth to
remove dust and dirt from the ventilation slots.
Regularly clean the sanding pad and the
sanding belt rollers to avoid inaccuracies
during use.

To remove the old sanding belt (12), proceed
as described in the section “Mounting and
removing the sanding belt”.
To mount the new sanding belt (12), proceed
as described in the section “Mounting and
removing the sanding belt”.
Checking and replacing the carbon brushes

The carbon brushes must be checked regularly.
If the carbon brushes are worn, the machine will
start to run unevenly.
2 Only use the correct type of carbon
brushes.
Remove the carbon brush holders (10) using
a screwdriver.
Clean the carbon brushes.
In case of wear, replace both carbon brushes
at the same time.
Mount the carbon brush holders (10) using
a screwdriver.
After mounting the new carbon brushes,
let the machine run at no load for 15 minutes.
WARRANTY
Consult the enclosed warranty terms.
ENVIRONMENT
Disposal
8
The product, the accessories, and the packaging
must be sorted for environmentally friendly
recycling.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BSM1022 - EBF-950 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BSM1022 - EBF-950 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info