632791
9
Zoom out
Zoom in
Previous page
1/60
Next page
Ferm 09
Explanation of symbols
In this manual and/or on the machine the following symbols are used:
Read instructions carefully
In accordance with essential applicable safety standards of European directives
Denotes risk of personal injury, loss of life or damage to the tool in case of non-
observance of the instructions in this manual.
Indicates electrical shock hazard.
Immediately unplug the plug from the mains electricity in the case that the cord
gets damaged and during maintenance
Keep bystanders away
Wear ear and eye protection
Faulty and/or discarded electrical or electronic apparatus have to be collected at
the appropriate recycling locations.
Special safety instructions
While sawing, never place your fingers where they could touch the saw band in case the
workpiece were to move unexpectedly.
Make sure that the saw band has the correct tension.
Make sure that the saw band is mounted with the teeth pointing down to avoid that the
workpiece is lifted unexpectedly.
Do not use saw bands designed for sawing wood.
Do not use saw bands which are bent, deformed, or otherwise damaged.
Never use the machine for sawing wood workpieces.
Never use the machine for sawing magnesium workpieces.
Never start sawing before the machine has reached full operational speed.
Securely tighten the workpiece. Never attempt to saw extremely small workpieces.
Do not leave the work area until the machine has been switched off and the saw band has
come to a complete standstill.
2. SAFETY INSTRUCTIONS
GB
D
NL
F
E
P
I
S
SF
N
DK
112
Ferm
Hvis vinklen ikke er 90°, justeres den som følger:
Løsn indstillingsskruen (36), og vip hovedet så savklingen kommer til at stå i en vinkel på
90°.
Løsn sikringsmøtrikken på stilleskruen (37), og skru stilleskruen ind eller ud for at opnå en
vinkel på 90°.
Drej sikringsmøtrikken fast igen.
Spænd stilleskruen.
Løsn skruen (38) og juster viseren (39), så den angiver 0°.
Drej skruen fast.
Indstilling af geringsvinklen
Fig. M
Geringsvinklen kan indstilles trinløst mellem 0° og 45°.
Løsn låseknappen (8) et par omgange.
Indstil den ønskede geringsvinkel ved hjælp af skalaen (40).
Stram låseknappen godt.
Fastspænding af arbejdsemnet
Fig. N
Drej klampen (9) en smule mere med hjulet (41) end arbejdsemnets tykkelse.
Sæt emnet op imod anslaget (35).
Stram skruestikken ved hjælp af hjulet, således at arbejdsemnet er godt fastspændt
mellem skruestikken og anlægget.
Brug altid skruestikken!
Brugsanvisning
Tænd maskinen, før arbejdsemnet berører savklingen.
Skub hovedet med jævn kraft nedad, så savklingen saver gennem arbejdsemnet og glider
ind i sprækken i bordet
Øv ikke tryk mod savklingen. Giv maskinen tid nok til at save arbejdsemnet.
Det bedste resultat opnås, når emnet ikke er tykkere end ca. 2,5 cm.
Vær forsigtig, når arbejdsemnet er mere end 2,5 cm tykt.
Maskinen arbejder mest effektivt, hvis slidte savklinger udskiftes i god tid.
Løft ikke savklingehylsteret op, før savklingen står helt stille.
Tænde og slukke
Fig. A
Maskinen er udstyret med en spændingsbeskyttelse; denne beskyttelse forhindrer utilsigtet
tænding af maskinen, når den tilsluttes netspændingen.
Indstil tænd-/slukknappen (1) til ‘I’for at tænde for maskinen.
Indstil tænd-/slukknappen til ‘0’for at slukke for maskinen.
UK
D
NL
F
E
P
I
S
SF
N
DK
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BSM1010 - FBS400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BSM1010 - FBS400 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info